2011-2016 FJ Cruiser · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jul 2007


1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B135590
    Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.

  1. B135598
    Install the front door window regulator with the 6 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Connect the connector.


3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

B138164
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not damage the glass.

  1. B135577
    Install the hole plug.


4. INSTALL FRONT DOOR WINDOW FRAME REAR LOWER

B138163
  1. Install the front door window frame rear lower, and temporarily tighten the bolt.


5. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

B138162
  1. Install the front door lower frame bracket garnish with the bolt and 2 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


6. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B138161
  1. Install the front door frame sub-assembly front lower with the screw.

  1. Temporarily tighten the bolt.


7. INSTALL FRONT DOOR GLASS RUN

B138160
  1. Install the front door glass run.

  1. B138163
    Tighten the front door window frame rear lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. B140037
    Tighten the front door frame sub-assembly front lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. B135578
    Install the hole plug.


8. INSTALL FRONT DOOR WEATHERSTRIP

B138159
  1. Install the front door weatherstrip.


9. INSTALL FRONT DOOR CHECK ASSEMBLY

B138158
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


10. INSTALL FRONT DOOR INSIDE PANEL PLATE

B135575
  1. Install the front door inside panel plate with the 4 screws.


11. INSTALL FRONT DOOR SERVICE HOLE COVER

B135576
  1. Apply butyl tape to the door panel, then install the new front door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links out through service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


12. INSTALL FRONT NO. 1 SPEAKER

  1. B130581
    Install the front No. 1 speaker with the 4 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

  1. B130580
    Connect the speaker connector.


13. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

  1. B135101
    Engage the 8 claws and install a new front door glass outer weatherstrip.

  1. B135099E01
    Remove the protective tape.


14. INSTALL OUTER REAR VIEW MIRROR

B138151
  1. Engage the 2 claws on the upper side of the mirror and the 6 clips and install the mirror.

    HINT:
    Heating the mirror holder with a domestic dryer before this procedure makes the work easier.

  1. B135564
    Install the outer rear view mirror with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


15. INSTALL FRONT NO. 2 DOOR SERVICE HOLE COVER

B135573
  1. Install the front No. 2 door service hole cover with the 4 screws.


16. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

B135572
  1. Connect the front door lock remote control cable and front door inside locking cable.

  1. B135571
    Engage the 10 clips and install the front door trim board.

  1. B135570
    Tighten the 2 screws.

  1. B140031
    for LH side:
    Close the 2 covers.

  1. B135569
    for RH side:
    Close the 2 covers.


17. INSTALL FRONT ARMREST BASE UPPER PANEL

B135557
  1. Connect the connector.

  1. Engage the 3 claws and clip and install the front armrest base upper panel.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

← INSPECTION (from Jul 2007)COMPONENTS (Jul 2007 – Oct 2010) →