2011-2016 FJ Cruiser · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jul 2007

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT ARMREST BASE UPPER PANEL

B135557
  1. Disengage the 3 claws and clip and remove the front armrest base upper panel.

  1. Disconnect the connector.


3. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

B140030E01
  1. for LH side:
    Using a screwdriver with its tip wrapped in protective tape, open the 2 covers.

  1. B135568E01
    for RH side:
    Using a screwdriver with its tip wrapped in protective tape, open the 2 covers.

  1. B135570
    Remove the 2 screws.

  1. B135571
    Disengage the 10 clips.

  1. B135572
    Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.


4. REMOVE FRONT NO. 2 DOOR SERVICE HOLE COVER

B135573
  1. Remove the 4 screws and front No. 2 door service hole cover.


5. REMOVE OUTER REAR VIEW MIRROR

B135564
  1. Driver side:
    Provisionally install the power window regulator master switch.

  1. Passenger side:
    Provisionally install the power window regulator switch.

  1. Close the door glass.

  1. Disconnect the connector.

  1. Remove the 3 bolts and the outer rear view mirror.

    NOTICE:
    Do not drop or damage the outer rear view mirror when removing the bolts.

  1. B140036E01
    Apply protective tape to the lower part of the mirror body.

  1. Press down the upper part of the mirror and tilt the mirror.

  1. B140035E01
    Using a screwdriver with its tip wrapped in protective tape, insert it between the mirror holder and the mirror holder base.

  1. B138150E01
    Twist and disengage the 2 clips on the lower side of the mirror.

    HINT:
    Heating the mirror holder with a domestic dryer before this procedure makes the work easier.

  1. While holding the mirror with the screwdriver, disengage the 4 clips and 2 claws on the upper side of the mirror and remove the mirror.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.


6. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

  1. B135099E01
    Apply protective tape to the front door panel in the area around the front door glass outer weatherstrip.

  1. B135100E01
    Using a moulding remover, disengage the 8 claws and remove the front door glass outer weatherstrip.


7. REMOVE FRONT NO. 1 SPEAKER

  1. B130580
    Disconnect the speaker connector.

  1. B130581
    Remove the 4 screws and the front No. 1 speaker.


8. REMOVE FRONT DOOR SERVICE HOLE COVER

B135574
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.


9. REMOVE FRONT DOOR INSIDE PANEL PLATE

B135575
  1. Remove the 4 screws and the front door inside panel plate.


10. REMOVE FRONT DOOR CHECK ASSEMBLY

B138158
  1. Remove the 2 nuts and bolt, then remove the front door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.


11. REMOVE FRONT DOOR WEATHERSTRIP

B138159
  1. Disengage the 24 clips and remove the front door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.


12. REMOVE FRONT DOOR GLASS RUN

B138160
  1. Remove the front door glass run.


13. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B135578
  1. Remove the hole plug.

  1. B138161
    Remove the bolt and screw, then remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolt and screw.


14. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

B138162
  1. Remove the bolt and the 2 screws and remove front door lower frame bracket garnish.


15. REMOVE FRONT DOOR WINDOW FRAME REAR LOWER

B138163
  1. Remove the bolt, then remove the front door window frame rear lower.

    NOTICE:
    Do not drop or damage the front door window frame rear lower when removing the bolt.


16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

B135577
  1. Remove the hole plug.

  1. Driver side:
    Provisionally install the power window regulator master switch.

  1. Passenger side:
    Provisionally install the power window regulator switch.

  1. Move the front door glass until the 2 bolts can be seen through the service holes.

  1. B138164
    Remove the 2 bolts.

  1. Pull the door glass upward to remove it.

    NOTICE:
    Do not damage the glass.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.


17. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

B135598
  1. Disconnect the connector.

  1. Remove the 6 bolts, then remove the front door window regulator.

    NOTICE:
    Do not drop or damage the front door window regulator.

    HINT:
    Remove the window regulator through the service hole.


18. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B135590
    Using "Torx" socket wrench T25, remove the 3 screws and the power window regulator motor.

← ON-VEHICLE INSPECTION (from Jul 2007)INSPECTION (from Jul 2007) →