2011-2016 FJ Cruiser · Service Manual SERVICE SPECIFICATIONS

SERVICE DATA

Specifications · Vehicles built from Jul 2007

Automatic Transmission System 
Line pressure
Engine idling
D position
356 to 426 kPa (3.6 to 4.3 kgf*cm2, 52 to 62 psi)
R position
522 to 622 kPa (5.3 to 6.3 kgf*cm2, 76 to 90 psi)
Line pressure
AT stall (Throttle valve fully opened)
D position
1,367 to 1,477 kPa (14.0 to 15.1 kgf*cm2, 198 to 214 psi)
R position
1,290 to 1,518 kPa (13.1 to 15.5 kgf*cm2, 187 to 220 psi)
Engine stall revolution
D position
2,250 to 2,550 rpm
Time lag
N → D position
Less than 1.2 seconds
N → R position
Less than 1.5 seconds
Engine idle speed
(A/C OFF)
N position
650 to 750 rpm
Drive plate runout
Max.
0.20 mm (0.0079 in.)
Torque converter runout
Max.
0.30 mm (0.0118 in.)
Torque converter clutch installation distance
23.28 mm (0.9166 in.) or more
Shift schedule
D position

(Throttle valve fully opened)
1 → 2
52 to 64 km/h (32 to 40 mph)
2 → 3
97 to 108 km/h (60 to 67 mph)
3 → 4
143 to 156 km/h (89 to 97 mph)
4 → 5
187 to 201 km/h (116 to 125 mph)
5 → 4
180 to 191 km/h (112 to 119 mph)
4 → 3
131 to 142 km/h (81 to 88 mph)
3 → 2
88 to 94 km/h (55 to 58 mph)
2 → 1
41 to 46 km/h (25 to 29 mph)
(Throttle valve fully closed)
4 → 5
48 to 54 km/h (30 to 34 mph)
5 → 4
29 to 34 km/h (18 to 21 mph)
4 position

(Throttle valve fully opened)
1 → 2
52 to 64 km/h (32 to 40 mph)
2 → 3
97 to 108 km/h (60 to 67 mph)
3 → 4
143 to 156 km/h (89 to 97 mph)
5 → 4
201 to 213 km/h (125 to 132 mph)
4 → 3
131 to 142 km/h (81 to 88 mph)
3 → 2
88 to 94 km/h (55 to 58 mph)
2 → 1
41 to 46 km/h (25 to 29 mph)
3 position
(Throttle valve fully opened)
1 → 2
52 to 64 km/h (32 to 40 mph)
2 → 3
97 to 108 km/h (60 to 67 mph)
4 → 3
140 to 151 km/h (87 to 94 mph)
3 → 2
88 to 94 km/h (55 to 58 mph)
2 → 1
41 to 46 km/h (25 to 29 mph)
2 position
(Throttle valve fully opened)
1 → 2
52 to 64 km/h (32 to 40 mph)
3 → 2
95 to 101 km/h (59 to 63 mph)
2 → 1
41 to 46 km/h (25 to 29 mph)
L position
(Throttle valve fully opened)
2 → 1
41 to 46 km/h (25 to 29 mph)
Lock-up point
Throttle valve opening 5%
D position
5th gear
Lock-up ON
76 to 82 km/h (47 to 51 mph)
Lock-up OFF
68 to 74 km/h (42 to 46 mph)
4 position
4th gear
Lock-up ON
72 to 78 km/h (45 to 48 mph)
Lock-up OFF
64 to 70 km/h (40 to 43 mph)
Automatic Transmission Unit 
1st and reverse return spring free length
Standard: 23.74 mm (0.9347 in.)
Rear planetary gear pinion thrust clearance
Standard: 0.2 to 0.6 mm (0.008 to 0.024 in.)
Rear planetary gear bushing inside diameter
Standard: 20.075 mm (0.7904 in.)
1st and reverse brake pack clearance
0.8 to 1.1 mm (0.031 to 0.043 in.)
Flange thickness (1st and reverse brake)
Mark 0: 0 mm (0 in.)
Mark 2: 0.2 mm (0.008 in.)
Mark 4: 0.4 mm (0.016 in.)
Mark 6: 0.6 mm (0.024 in.)
Mark 8: 0.8 mm (0.031 in.)
Mark 10: 1.0 mm (0.039 in.)
Mark 12: 1.2 mm (0.047 in.)
Mark 14: 1.4 mm (0.055 in.)
Intermediate shaft run out
Standard: 0.08 mm (0.003 in.)
Intermediate shaft diameter
Standard A: 25.962 to 25.975 mm (1.022 to 1.023 in.)
Standard B: 25.962 to 25.975 mm (1.022 to 1.023 in.)
Standard C: 32.062 to 32.075 mm (1.262 to 1.263 in.)
Standard D: 32.062 to 32.075 mm (1.262 to 1.263 in.)
Rear planetary ring gear flange bushing inside diameter
Standard: 32.18 mm (1.2667 in.)
Center planetary gear pinion thrust clearance
Standard: 0.12 to 0.68 mm (0.005 to 0.027 in.)
Brake piston return spring No.2 free length
Standard: 17.45 mm (0.687 in.)
Brake piston return spring free length
Standard: 17.05 mm (0.671 in.)
Front planetary gear pinion thrust clearance
Standard: 0.20 to 0.60 mm (0.008 to 0.024 in.)
Front planetary gear bushing inside diameter
Standard: 57.48 mm (2.263 in.)
Brake piston No.1 piston stroke
0.42 to 0.72 mm (0.017 to 0.028 in.)
Flange thickness (brake piston No.1)
Mark 0: 2.0 mm (0.079 in.)
Mark 1: 2.2 mm (0.087 in.)
Mark 2: 2.4 mm (0.094 in.)
Mark 3: 2.6 mm (0.102 in.)
Brake piston return spring No.3 free length
Standard: 15.72 mm (0.619 in.)
Oil Pump 
Body clearance
Standard: 0.10 to 0.17 mm (0.0039 to 0.0067 in.)
Maximum: 0.17 mm (0.0067 in.)
Tip clearance
Standard: 0.07 to 0.15 mm (0.0028 to 0.0059 in.)
Maximum: 0.15 mm (0.0059 in.)
Side clearance
Standard: 0.02 to 0.05 mm (0.0008 to 0.0020 in.)
Maximum: 0.05 mm (0.0020 in.)
Drive and driven gear thickness
Mark 0: 10.740 to 10.749 mm (0.4228 to 0.4232 in.)
Mark 1: 10.750 to 10.759 mm (0.4232 to 0.4236 in.)
Mark 2: 10.760 to 10.769 mm (0.4236 to 0.4240 in.)
Mark 3: 10.770 to 10.779 mm (0.4240 to 0.4244 in.)
Mark 4: 10.780 to 10.789 mm (0.4244 to 0.4248 in.)
Starter shaft bushing inside diameter
Standard (Front side): 21.577 mm (0.850 in.)
Standard (Rear side): 32.08 mm (1.263 in.)
Front oil pump body inside diameter
38.188 mm (1.504 in.)
Clutch Drum and Input Shaft 
Direct clutch
Pack clearance
0.50 to 0.80 mm (0.020 to 0.032 in.)
Clutch piston return spring free length
Standard: 19.51 mm (0.768 in.)
Flange thickness
No. 0: 3.0 mm (0.118 in.)
No. 1: 3.1 mm (0.122 in.)
No. 2: 3.2 mm (0.126 in.)
No. 3: 3.3 mm (0.130 in.)
No. 4: 3.4 mm (0.134 in.)
No. 5: 3.5 mm (0.138 in.)
No. 6: 3.6 mm (0.142 in.)
No. 7: 3.7 mm (0.146 in.)
No. 8: 3.8 mm (0.150 in.)
Reverse clutch
Reverse clutch hub busing inside diameter
Standard: 35.812 to 35.837 mm (1.4099 to 1.4109 in.)
Maximum: 35.887 mm (1.4129 in.)
Pack clearance
0.50 to 0.80 mm (0.020 to 0.032 in.)
Clutch piston return spring free length
Standard: 21.04 mm (0.828 in.)
Flange thickness
No. 0: 2.8 mm (0.110 in.)
No. 1: 2.9 mm (0.114 in.)
No. 2: 3.0 mm (0.118 in.)
No. 3: 3.1 mm (0.122 in.)
No. 4: 3.2 mm (0.126 in.)
No. 5: 3.3 mm (0.130 in.)
No. 6: 3.4 mm (0.134 in.)
No. 7: 3.5 mm (0.138 in.)
No. 8: 3.6 mm (0.142 in.)
No. 9: 3.7 mm (0.146 in.)
No. A: 3.8 mm (0.150 in.)
Froward clutch
Forward clutch hub bushing inside diameter
Standard: 26.037 to 26.062 mm (1.0251 to 1.0261 in.)
Maximum: 26.112 mm (1.028 in.)
Pack clearance
0.60 to 0.90 mm (0.024 to 0.035 in.)
Clutch piston return spring free length
Standard: 26.74 mm (1.053 in.)
Flange thickness
No. 0: 3.0 mm (0.118 in.)
No. 1: 3.1 mm (0.122 in.)
No. 2: 3.2 mm (0.126 in.)
No. 3: 3.3 mm (0.130 in.)
No. 4: 3.4 mm (0.134 in.)
No. 5: 3.5 mm (0.138 in.)
No. 6: 3.6 mm (0.142 in.)
No. 7: 3.7 mm (0.146 in.)
No. 8: 3.8 mm (0.150 in.)
No. 9: 3.9 mm (0.154 in.)
No. A: 4.0 mm (0.158 in.)
Accumulator 
Spring
Free Length/Outer diameter
Color
B-3
70.5 mm (2.776 in.)/19.7 mm (0.776 in.)
Purple
C-2
62.0mm (2.441)/15.9 mm (0.626 in.)
White
C-1 (Inner)
30.4 mm (1.197 in.)/11.4 mm (0.449 in.)
Pink
C-1 (Outer)
48.76 mm (1.920 in.)/16.6 mm (0.654 in.)
Light green
C-3 (Inner)
44.0 mm (1.732 in.)/14.0 mm (0.551 in.)
Yellow
C-3 (Outer)
73.35 mm (2.888 in.)/19.9 mm (0.784 in.)
Red
← TORQUE SPECIFICATIONS (from Aug 2009)TORQUE SPECIFICATIONS (from Jul 2007) →