2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Nov 2010 – Jul 2013

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL WATER INLET WITH THERMOSTAT
  1. Install a new gasket and the water inlet with thermostat with the 3 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


2. CONNECT NO. 2 RADIATOR HOSE

  1. A226655E01
    Connect the radiator hose to the water inlet with the hose clamp.
    Text in Illustration 
    *a
    View A
    *b
    Upper Side
    *c
    Front Side

    HINT:
    Perform the installation with the hose clip at the correct angle.


3. ADD ENGINE COOLANT
  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. A220212E02
    Slowly pour coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *1
    FULL Line

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. A220212E02
    If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the Full line.
    If the coolant level is below the Full line, repeat steps *4 through *8.
    If the coolant level is above the Full line, drain coolant until the coolant level reaches the Full line.
    Text in Illustration 
    *1
    FULL Line


4. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. A220211E01
    Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester


5. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Hook the engine under cover to the frame.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


6. INSTALL V-BANK COVER
  1. Engage the 2 V-bank cover hooks to the bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.

← INSTALLATION (Aug 2009 – Oct 2010)INSTALLATION (Aug 2013 – Jul 2014) →