INSTALLATION
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2009 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
| 1. INSTALL INTAKE MANIFOLD |
Set a new gasket on each cylinder head.

- NOTICE:
- Align the port holes of the gasket and cylinder head.
- Be careful of the installation direction.
- Align the port holes of the gasket and cylinder head.
Set the intake manifold on the cylinder heads.
Install and uniformly tighten the 6 bolts and 4 nuts in several passes.

Text in Illustration *1
Nut
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
- HINT:
- Tighten the inner installation bolts of the intake manifold before tightening the outer bolts.
| 2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.

Text in Illustration *a
Turn
Temporarily install the 6 bolts, which are used to hold the fuel delivery pipe, to the intake manifold.
Check that the fuel injectors rotate smoothly.
- HINT:
- If the fuel injectors do not rotate smoothly, replace the O-ring of any injector that does not rotate smoothly.
Position the fuel injector connectors facing outward.
Tighten the 6 bolts, which are used to hold the fuel delivery pipe, to the intake manifold.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Connect the 6 fuel injector connectors.
| 3. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY |
Connect the No. 2 fuel pipe sub-assembly (Click here).
- NOTICE:
- Check that there are no scratches or foreign objects on the connecting part.
- If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
- After connecting, check that the pipe and connector are securely connected by pulling on them.
- Check that there are no scratches or foreign objects on the connecting part.
| 4. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY |
Connect the No. 1 fuel pipe sub-assembly (Click here).
- NOTICE:
- Check that there are no scratches or foreign objects on the connecting part.
- If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
- After connecting, check that the pipe and connector are securely connected by pulling on them.
- Check that there are no scratches or foreign objects on the connecting part.
| 5. INSTALL REAR CYLINDER HEAD COVER |
Temporarily install the cover with the 3 bolts.
Tighten the 3 bolts in the sequence shown in the illustration.

- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
| 6. INSTALL INTAKE AIR SURGE TANK |
Install a new gasket to the intake air surge tank.
Install the intake air surge tank in the order shown in the illustration.
Using a 8 mm socket hexagon wrench, temporarily tighten the 4 bolts to the intake air surge tank.

Temporarily tighten the 2 nuts to the intake air surge tank.
Text in Illustration 

Nut
Tighten the 4 bolts and 2 nuts.
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
Install the No. 2 surge tank stay with the 2 bolts in the order shown in the illustration.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Install the No. 1 surge tank stay with the 2 bolts in the order shown in the illustration.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Engage the wire harness clamp.
Install the throttle body bracket with the 2 bolts in the order shown in the illustration.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Connect the No. 1 ventilation hose.

Text in Illustration *a
Front
Connect the No. 1 vacuum switching valve connector.

Text in Illustration *a
Front
*b
Matchmark
*c
Top
Connect the No. 1 fuel feed hose.
- HINT:
- Connect the hose so that the direction of the hose clamp is as indicated in the illustration.
Connect the throttle body connector.
Connect the No. 4 water by-pass hose.

Text in Illustration *a
RH
*b
Rear
*c
Top
*d
Matchmark
- HINT:
- Connect the hose so that the direction of the hose clamp is as indicated in the illustration.
Connect the No. 5 water by-pass hose.
- HINT:
- Connect the hose so that the direction of the hose clamp is as indicated in the illustration.
Connect the 2 heater hose clamps.
| 7. INSTALL AIR CLEANER HOSE ASSEMBLY |
Install the air cleaner hose assembly with the 2 hose clamps.

- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Text in Illustration *a
Protrusion
*b
Groove
*c
Top
*d
RH
*e
Front
*f
Paint mark of the hose
Install the bolt.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Connect the vacuum hose and ventilation hose.
- HINT:
- Connect the hose so that the direction of the hose clamp is as indicated in the illustration.
Engage the wire harness clamp.
| 8. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
Tighten the radiator drain cock plug by hand.
Remove the vinyl hose from the radiator drain cock of the radiator assembly.
Add engine coolant.
- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
9.8 liters (10.4 US qts, 8.6 Imp. qts)
for Manual Transmission
9.4 liters (9.9 US qts, 8.3 Imp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the engine coolant level. If the engine coolant level is low, add engine coolant.
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.

Text in Illustration *a
Full Line
Install the radiator reserve tank cap sub-assembly.
Install the radiator cap sub-assembly.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3
Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.
- HINT:
- Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator assembly if the engine is warmed up and the thermostat opens.
Install the radiator cap sub-assembly.*4
Set the air conditioning as follows.*5
Item
Condition
Fan speed
Any setting except off
Temperature
Toward WARM
Air conditioning switch
Off
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6
- CAUTION:
- Wear protective gloves. Hot areas on the parts may injure your hands.
- Be careful of the fan.
- Be careful as the engine, radiator assembly and radiator hoses are hot and can cause burns.
- Wear protective gloves. Hot areas on the parts may injure your hands.
- NOTICE:
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
- Do not start the engine when there is no engine coolant in the radiator reservoir.
- Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
- If there is not enough engine coolant, the engine may burn out or overheat.
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
- HINT:
- Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
- The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.
- Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7
- CAUTION:
- Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8
If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.

If the engine coolant level is below the Full line, repeat steps *4 through *8.
If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.Text in Illustration *a
Full Line
Install the service hole cover to the engine under cover.
| 9. INSPECT FOR COOLANT LEAK |
- CAUTION:
- To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.
Fill the radiator with engine coolant, and then attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.

If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.Text in Illustration *1
Radiator Cap Tester
| 10. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
- NOTICE:
- Do not start the engine.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed / ON.
Check fuel pump operation.
Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.
| 11. INSTALL V-BANK COVER |
Engage the 2 V-bank cover hooks to the bracket.
Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.
