Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Condition
Trouble Area
P0116
When either of following conditions met (2 trip detection logic):
  1. During engine warming up after cold engine starts, change in Engine Coolant Temperature (ECT) sensor output below threshold
  2. In duration between warmed engine stopped and next cold engine start, change in ECT sensor output below threshold
  1. Water inlet with thermostat
  2. ECT sensor
P0116
For Mexico Models:
Case 1:
Engine Coolant Temperature (ECT) between 35°C and 60°C (95°F and 140°F) when engine started, and conditions (a) and (b) met (2 trip detection logic)
  1. (a) Vehicle driven at varying speeds (accelerated and decelerated)
  2. (b) ECT remains within 3°C (5.4°F) of initial ECT
Case 2:
ECT more than 60°C (140°F) when engine started, and conditions (a) and (b) met (6 trip detection logic)
  1. (a) Vehicle driven at varying speeds (accelerated and decelerated)
  2. (b) ECT measurements remain within 1°C (1.8°F) of initial ECT on 6 successive occasions
  1. Water inlet with thermostat
  2. ECT sensor

MONITOR DESCRIPTION

  1. Engine coolant temperature (ECT) sensor cold start monitor
    When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
  1. ECT sensor soak monitor
    If the ECT sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
  1. ECT sensor high side stuck monitor (only for Mexico models)
    The ECM monitors the sensor voltage and uses this value to calculate the ECT. If the sensor voltage output deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the ECT sensor and stores the DTC.
Examples:
  1. Upon starting the engine, the ECT is between 35 and 60°C (95 and 140°F). If after driving for 250 seconds, the ECT remains within 3°C (5.4°F) of the starting temperature, the DTC is stored (2 trip detection logic).
  2. Upon starting the engine, the ECT is over 60°C (140°F). If after driving at varying speeds (accelerating and decelerating) for a specified period of time, the ECT remains within 1°C (1.8°F) of the starting temperature, the DTC is stored (6 trip detection logic).

MONITOR STRATEGY


Related DTCs
P0116: Engine coolant temperature sensor cold start monitor
P0116: Engine coolant temperature sensor soak monitor
Required Sensors/Components (Main)
Engine coolant temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
-: Cold start monitor
10 seconds: Soak monitor
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


ECT Sensor Cold Start Monitor 
Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or more
Time after engine start
1 second or more
ECT at engine start
Less than 60°C (140°F)
IAT sensor circuit fail (P0112, P0113)
Not detected
ECT sensor circuit fail (P0115, P0117, P0118, P0125)
Not detected
Thermostat fail (P0128)
Not detected
Soak time
0 seconds or more
Accumulated MAF
9597 g or more
Engine
Running
Fuel cut
OFF
Difference between ECT at engine start and IAT
Less than 40°C (72°F)

ECT Sensor Soak Monitor: 
Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or more
Engine
Running
IAT sensor circuit fail (P0112, P0113)
Not detected
ECT sensor circuit fail (P0115, P0117, P0118, P0125)
Not detected
Thermostat fail (P0128)
Not detected
Soak timer circuit fail (P2610)
Not detected
Soak time
5 hours or more
Either (a) or (b) condition met
-
(a) ECT
60°C (140°F) or more
(b) Accumulated MAF
19194 g or more

TYPICAL MALFUNCTION THRESHOLDS


ECT Sensor Cold Start Monitor 
ECT sensor value change
Less than 5°C (9°F)

ECT Sensor Soak Monitor 
Difference between current ECT sensor value and previous ECT sensor value when engine stopped
Less than 5°C (9°F) (varies with last trip ECT)

COMPONENT OPERATING RANGE


ECT
ECT sensor value changes in accordance with actual ECT

CONFIRMATION DRIVING PATTERN


A198823E38

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Enter the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
  4. Check that the coolant temperature is 60°C (140°F) or less.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON and turn the Techstream on [A].
  8. Start the engine and idle it for 5 minutes or more [B].

    HINT:
    If the engine coolant temperature does not change by 5°C (9°F) or more, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0116.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].

  14. Drive the vehicle at 40 km/h (25 mph) or more for a total of 10 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.

  15. Check the DTC judgment result again [E].

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0117, P0118 or P0125 are output simultaneously with DTC P0116, the ECT sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  3. When the DTC is output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

Result 
Result
Proceed To
P0116 is output
A
P0116 and other DTCs are output
B

HINT:
If any DTCs and other than P0116 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT WATER INLET WITH THERMOSTAT
  1. Remove the water inlet with thermostat (Click here).

  1. Check the valve opening temperature of the thermostat (Click here).

    Standard opening temperature:
    80°C to 84°C (176°F to 183°F)

    HINT:
    1. In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.
    2. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE WATER INLET WITH THERMOSTAT (Click here)
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)