WIPER AND WASHER SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU |


Disconnect the 1A, 1B, 1E, and 1H main body ECU connectors.
Measure the voltages and resistances of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND1 (1H-2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| BECU (1B-4) - Body ground | W-R - Body ground | Power source circuit (From battery) | Always | 11 to 14 V |
| BDR1 (1E-9) - Body ground | B-Y - Body ground | Power source circuit (From battery) | Always | 11 to 14 V |
| GND1,2 (1H-2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the main body ECU connectors.
Measure the voltages of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| WMTR (1B-1) - GND1,2 (1H-2) | B-O - W-B | Rear washer motor output | Rear washer motor OFF | Below 1 V |
| Rear washer motor ON | 10 to 14 V | |||
| SIG (1F-8) - GND1,2 (1H-2) | B-R - W-B | ECU power supply (from ignition switch) | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 14 V | |||
| MPX2 (E6-23) - GND1, 2 (1H-2) | BR-R - W-B | Multiplex communication signal | Ignition switch ON | Signal waveform |
| WRIN (E8-9) - GND1, 2 (1H-2) | BR-W - W-B | Rear wiper switch signal | Ignition switch ON and rear wiper switch OFF | 10 to 14 V |
| Ignition switch ON and wiper switch LO | Below 1 V | |||
| WRLO (E8-10) - GND1, 2 (1H-2) | GR-R - W-B | Rear wiper switch signal | Ignition switch ON and rear wiper switch OFF | 10 to 14 V |
| Ignition switch ON and rear wiper switch HI | Below 1 V | |||
| RWSW (E7-1) - GND1, 2 (1H-2) | LG-B - W-B | Rear washer switch signal | Ignition switch ON and rear washer switch OFF | 10 to 14 V |
| Ignition switch ON and rear washer switch ON | Below 1 V |
| CHECK BACK DOOR ECU |

Disconnect the S2 back door ECU connector.
Measure the voltages and resistances of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| BECU (S2-5) - Body ground | W-R - Body ground | Power source circuit (From battery) | Always | 11 to 14 V |
| GND (S2-3) - Body ground) | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the back door ECU connector.
Measure the voltages of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| BDR (S2-4) - GND (S2-3) | L-O - W-B | Power supply (from battery) | Always | 11 to 14 V |
| SIG (S2-6) - GND (S2-3) | B-R - W-B | ECU power supply (from ignition switch) | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| WIP- (S5-1) - GND (S2-3) | R-G - W-B | Rear wiper motor output | Ignition switch ON and wiper switch LO or HI | Pulse generation |
| WIP+ (S5-2) - GND (S2-3) | Y-G - W-B | Rear wiper motor output | Ignition switch ON and wiper switch LO or HI | Pulse generation |
| W (S5-3) - GND (S2-3) | BR-B - W-B | Rear wiper reverse position switch signal | Ignition switch ON | Pulse generation |
| P (S5-12) - E (S5-19) | P-B - V-G | Rear wiper housing position switch signal | Ignition switch ON | Below 1 V |
| GCTY (S5-10) - GND (S2-3) | B-O - W-B | Back window door courtesy switch signal | Back window door closed | 11 to 14 V |
| Back window door open | Below 1 V | |||
| MPX2 (S2-1) - GND (S2- 3) | BR-R - W-B | Multiplex communication signal circuit | During communication | Signal waveform |