THROTTLE BODY > INSTALLATION |
| 1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY |
![]() |
Install a new gasket to the intake air surge tank assembly.
| *a | Recess |
| *b | New Gasket |
Install the throttle with motor body assembly with the 4 bolts.
Connect the throttle body connector.
![]() |
Connect the No. 4 water by-pass hose.
| *a | RH |
| *b | Rear |
| *c | Top |
| *d | Matchmark |
Connect the No. 5 water by-pass hose.
| 2. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose assembly to the air cleaner cap sub-assembly and intake air surge tank with the 2 hose clamps.
| *a | View A |
| *b | View B |
| *c | Hose Paint Mark |
| *d | Upper of Vehicle |
| *e | Protrusion of Air Cleaner Cap Sub-assembly |
| *f | Protrusion of Intake Air Surge Tank |
| *g | Indentation of Air Hose Assembly |
Connect the air cleaner hose assembly to the resonator bracket with the bolt.
Engage the clamp and connect the wire harness to the air cleaner hose assembly.
Connect the vacuum hose to the air cleaner hose assembly.
Connect the ventilation hose to the air cleaner hose assembly with the hose clip.
| 3. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug.
Tighten the radiator drain cock plug by hand.
Remove the vinyl hose from the radiator drain cock of the radiator assembly.
Add engine coolant.
| Item | Specified Condition |
| for Automatic Transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
| for Manual Transmission | 9.4 liters (9.9 US qts, 8.3 Imp. qts) |
![]() |
Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.
| *a | Full Line |
Install the radiator reserve tank cap sub-assembly.
Install the radiator cap sub-assembly.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3
Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.
Install the radiator cap sub-assembly.*4
Set the air conditioning as follows.*5
| Item | Condition |
| Fan speed | Any setting except off |
| Temperature | Toward WARM |
| Air conditioning switch | Off |
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6
Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7
If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8
![]() |
If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.
If the engine coolant level is below the Full line, repeat steps *4 through *8.
If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.
| *a | Full Line |
Install the service hole cover to the engine under cover.
| 4. INSPECT FOR ENGINE COOLANT LEAK |
Fill the radiator with engine coolant, and then attach a radiator cap tester.
Warm up the engine.
![]() |
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| *1 | Radiator Cap Tester |
| 5. INSTALL V-BANK COVER |
Engage the 2 hooks and install the V-bank cover to the No. 1 V-bank cover bracket.
Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.
| 6. PERFORM INITIALIZATION |
Disconnect the cable from the negative (-) battery terminal. Wait at least 60 seconds and reconnect the cable.
Turn the ignition switch to ON without operating the accelerator pedal.
Connect the Techstream to the DLC3 and clear the DTCs (Click here).
Perform the "Inspection After Repairs" (Click here).
Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.
| Condition | Engine Idle Speed |
| A/C switched off | 580 to 680 rpm |
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.
Perform a road test and confirm that there are no abnormalities.