Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › COMPRESSOR

COMPRESSOR > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL


I105421E01
  1. When replacing the compressor with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor before installation, so that the amount of oil contained in it is the same as that in the compressor to be replaced.

    HINT:
    New compressors are filled with sufficient oil for the whole cycle. Therefore, it is necessary to drain residual oil from the condenser and cooling unit.

    Standard:
    (The amount of oil inside a new compressor: 120 (+15) cc (4.1 (+0.51) fl.oz.)) - (The amount of oil remaining in the removed compressor) = The amount of oil to be removed when replacing the compressor

    NOTICE:
    1. When checking the compressor oil level, observe the precautions for cooler removal/installation.
    2. If a new compressor is installed without removing the amount of oil remaining in the pipes of the vehicle, the amount of oil becomes too large. This prevents heat exchange in the refrigerant cycle and causes refrigeration failure.
    3. If the amount of oil remaining in the removed compressor is too small, check for oil leakage.
    4. Use ND-OIL8 compressor oil.



2. INSTALL COOLER COMPRESSOR ASSEMBLY


I105350E01
  1. Using a "TORX" socket wrench (E8), install the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Temporary install the cooler compressor with the 3 bolts.

  1. Tighten the nut.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Tighten the 3 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts in the order shown in the illustration.

  1. Connect the connector.



3. INSTALL DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the discharge hose.

  1. Install the discharge hose onto the compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



4. INSTALL SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor.

    Compressor oil:
    ND-OIL8 or the equivalent

  1. Install the O-ring onto the suction hose.

  1. Install the suction hose onto the compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the suction hose with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



5. INSTALL NO. 2 ENGINE WIRE
  1. Install the 3 bolts, nut and the No. 2 engine wire.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } for Bolt

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for Nut

  1. Close the cover to terminal 30.

  1. Connect the clamp and No. 2 engine wire.

  1. Install the ground wire with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



6. INSTALL FRONT FENDER REAR SPLASH SHIELD LH
  1. Install the front fender rear splash shield with the 5 clips.



7. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the front fender apron seal with the 5 clips.



8. INSTALL FAN AND GENERATOR V BELT
  1. Install the fan and generator V belt (Click here).



9. CHARGE REFRIGERANT



I100449E06

NOTICE:
Charge refrigerant in accordance with equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    570 to 630 g (20.11 to 22.22 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I101544E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      Shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and thus refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



10. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2,000 rpm for 2 minute or more after charging it with refrigerant.



11. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.



    I100587E02
  1. Bring the halogen leak detector close to the drain hose before performing the test.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
    2. Place the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.

    If such a reaction is unavoidable, the vehicle must be lifted up.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.