WINDSHIELD GLASS > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE WINDSHIELD WIPER ARM COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 3 front wiper arm cover.
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE) |
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 6. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY |
![]() |
Using a 8 mm (5/16 inch) wrench, remove the radio antenna pole sub-assembly by turning it counterclockwise.
| 7. REMOVE ANTENNA ORNAMENT |
![]() |
Pull out the antenna ornament vertically.
| 8. REMOVE FRONT FENDER SIDE PANEL UPPER RH |
![]() |
Disengage the 4 clips and remove the front fender side panel upper RH.
Remove the 4 clips from the front fender side panel upper RH.
| 9. REMOVE FRONT FENDER SIDE PANEL UPPER LH |
![]() |
Disengage the 4 clips and remove the front fender side panel upper LH.
Remove the 4 clips from front fender side panel upper LH.
| 10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 7 clips and remove the cowl top ventilator louver sub-assembly.
| 11. REMOVE COWL TOP VENTILATOR LOUVER RH |
![]() |
Disengage the clip and remove the hood to cowl top seal.
Remove the 3 clips and the claw, and remove the cowl top ventilator louver RH.
| 12. REMOVE COWL TOP VENTILATOR LOUVER LH |
![]() |
Remove the 5 clips.
Disengage the 7 claws and remove the cowl top ventilator louver LH.
| 13. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Disengage the 14 claws and remove the front door scuff plate.
| 14. REMOVE FRONT DOOR SCUFF PLATE LH |
| 15. REMOVE ACCESS DOOR SCUFF PLATE RH |
![]() |
Disengage the 6 claws and remove the access door scuff plate.
| 16. REMOVE ACCESS DOOR SCUFF PLATE LH |
| 17. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 4 claws and remove the front floor footrest.
| 18. REMOVE FOOTREST CLIP |
![]() |
Remove the 2 footrest clips.
| 19. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
| 20. REMOVE COWL SIDE TRIM BOARD LH |
| 21. REMOVE ROOF SIDE INNER GARNISH COVER RH |
![]() |
| *1 | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.
| 22. REMOVE ROOF SIDE INNER GARNISH COVER LH |
| 23. REMOVE ROOF SIDE RAIL GARNISH RH |
![]() |
Remove the 2 bolts.
Disengage the claw and the guide remove the roof side rail garnish.
| 24. REMOVE ROOF SIDE RAIL GARNISH LH |
| 25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 26. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 27. REMOVE ASSIST GRIP PLUG |
![]() |
| *1 | Protective Tape |
| *a | for RH Side |
| *b | for LH Side |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
| 28. REMOVE ASSIST GRIP ASSEMBLY |
![]() |
| *a | for RH Side |
| *b | for LH Side |
Remove the 2 screws and the assist grip.
| 29. REMOVE VISOR SUB-ASSEMBLY RH |
![]() |
Disengage the 2 claws and remove the visor sub-assembly.
| *a | for RH Side |
| *b | for LH Side |
| 30. REMOVE VISOR SUB-ASSEMBLY LH |
| 31. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Disengage the 2 clips and the guide and remove the front pillar garnish.
| 32. REMOVE FRONT PILLAR GARNISH LH |
| 33. REMOVE VISOR ASSEMBLY RH |
![]() |
Remove the visor support shaft from the visor holder.
Remove the 2 screws and the visor.
| 34. REMOVE VISOR ASSEMBLY LH |
| 35. REMOVE VISOR HOLDER |
![]() |
| *a | for RH Side |
| *b | for LH Side |
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
| 36. REMOVE INNER REAR VIEW MIRROR ASSEMBLY |
| 37. REMOVE PERSONAL LIGHT ASSEMBLY (w/ CRAWL) |
![]() |
Using a moulding remover, disengage the 4 clips and 4 guides.
![]() |
Disconnect the connector and remove the personal light assembly.
| *1 | Grommet |
| *2 | Pin |
Remove the 4 pins.
Remove the 4 grommets from the body side.
| 38. REMOVE ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
![]() |
Disengage the roof wire from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
Remove room light bulb No. 1.
| 39. REMOVE ROOF HEADLINING |
| 40. REMOVE WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY |
![]() |
Apply protective tape to the roof panel in the area around the windshield outside upper moulding.
| *1 | Protective Tape |
![]() |
Insert the piano wires between the vehicle body and the windshield outside upper moulding, as shown in the illustration.
| *1 | Wooden Block |
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
![]() |
Disengage the 4 claws and the 2 clips and remove the windshield outside upper moulding.
| 41. REMOVE ROOF DRIP SIDE FINISH MOULDING RETAINER |
![]() |
Remove the screw and the roof drip side finish moulding retainer.
| 42. REMOVE FRONT PILLAR OUTER GARNISH |
![]() |
Remove the nut.
Disengage the 5 clips and remove the front pillar outer garnish.
| 43. REMOVE ROOF SIDE GARNISH PROTECTOR |
![]() |
Using a clip remover, remove the 4 clips.
Remove the 3 pieces of double-sided adhesive tape and the roof side garnish protector.
| 44. REMOVE WINDSHIELD OUTSIDE LOWER MOULDING |
![]() |
Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
![]() |
Disengage the 6 claws and remove the windshield outside lower moulding.
| 45. REMOVE WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a knife, cut off the windshield outside moulding, as shown in the illustration.
Remove the windshield outside moulding.
| 46. REMOVE WINDSHIELD GLASS |
![]() |
Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
![]() |
Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.
Cut through the adhesive by pulling the piano wire around the windshield glass.
![]() |
Disengage the 2 stoppers.
Using suction cups, remove the windshield glass.