Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > INSTALLATION

for Preparation Click here



1. CLEAN QUARTER WINDOW GLASS


BO04421E01
  1. Clean the outer circumference of the glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Even if using a new glass, clean the glass with a non-residue solvent.



2. CLEAN VEHICLE BODY


    B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.



3. INSTALL QUARTER WINDOW GLASS


H002865E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



    B139424E01
  1. Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    Specification:
    Area
    Measurement
    a
    20 mm (0.787 in.)
    b
    17.3 mm (0.681 in.)
    c
    26 mm (1.024 in.)
    d
    20 mm (0.787 in.)
    e
    20 mm (0.787 in.)
    f
    5 mm (0.197 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.



    B140014E01
  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or the equivalent


    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      27.3 mm (1.075 in.)
      d
      8 mm (0.315 in.)
      e
      8 mm (0.315 in.)
      f
      10 mm (0.394 in.)
      g
      14 mm (0.551 in.)



  1. Install the quarter window glass onto the body.

    1. Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the pins are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.



    3. B073131E02
    4. Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the quarter window glass rim.

      NOTICE:
      Do not drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



4. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.

  1. Seal any leakage with auto glass sealer.



5. INSTALL ROOF SIDE INNER GARNISH RH


    B130622
  1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

  1. Engage the 7 clips and the claw and install the roof side inner garnish.

  1. Tighten the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install the clip.



    B130621
  1. Engage the claw and close the cover.



6. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Install the 3 screws.

  1. Install the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Install the 3 screws.



9. INSTALL REAR DECK TRIM COVER (w/ Power Outlet Socket)


    B138600
  1. Connect the power outlet connector.



    B135130
  1. Engage the 8 claws and install the rear deck trim cover.



10. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
  1. Install the anchor plate with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Make sure that the anchor plate rotates smoothly.



11. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



12. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the lap belt outer anchor cover.



13. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)


    B134990
  1. Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Connect the speaker connector.



14. INSTALL SPEAKER MOUNTING COVER (w/ Woofer)


    B134991
  1. Engage the 8 clips and install the speaker mounting cover.



15. INSTALL DECK SIDE GARNISH (w/ Woofer)


    B134992
  1. Engage the 6 claws and install the deck side garnish.



16. INSTALL QUARTER TRIM POCKET (w/o Woofer)


    B130613
  1. Engage the 6 claws and install the quarter trim pocket.



17. INSTALL SIDE TRIM COVER (w/o Woofer)


    B130612
  1. Engage the 8 claws and install the side trim cover.



18. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)


    B130611
  1. Engage the 7 claws and install the quarter trim pocket tray.



19. INSTALL PACKAGE HOLDER NET HOOK

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }



20. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B130604E02
  1. Align the locating marks with the paint marks first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Text in Illustration 
    *a
    Locating Mark
    *b
    Paint Mark

    Paint mark:
    Area
    Color
    RH side
    White
    LH side
    Red



21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



22. INSTALL REAR DOOR SCUFF PLATE RH


    B130598
  1. Engage the 6 claws and install the access door scuff plate.



23. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



24. INSTALL FRONT DOOR SCUFF PLATE RH


    B130597
  1. Engage the 14 claws and install the door scuff plate.



25. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



26. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


B179163E01

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.



27. INSTALL REAR FLOOR MAT ASSEMBLY


    B130594
  1. Install the rear floor mat with the 2 clips.



28. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B130593
  1. Engage the 11 claws and install the rear floor mat support plate.



    B130592
  1. Tighten the 5 screws.



29. INSTALL REAR FLOOR BOARD


    B135075
  1. Engage the clip and claw and install the rear floor board.



    B135074E02
  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.



30. INSTALL REAR SEATBACK ASSEMBLY RH


    B130750E01
  1. Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.



    B135128E02
  1. Install the rear seat inner belt into the rear seatback holder.
    Text in Illustration 
    *a
    Convex

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.



31. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.



32. INSTALL REAR SEATBACK ASSEMBLY LH


    B130721E01
  1. Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Install the rear center seat inner belt into the rear seatback holder.



33. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
  1. Engage the 8 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.



34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }