Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY

E125398E02

  1. Disconnect the E13 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-1 (B) - Body ground
    R - Body ground
    Battery
    Always
    11 to 14 V
    E13-2 (IG+) - Body ground
    R-L - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1 V → 11 to 14 V
    E13-21 (ES) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the combination meter assembly connector.

  4. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-7 (WRNP) - Body ground
    LG - Body ground
    Seat belt warning light signal (Front passenger side)
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is unfastened
    Alternating between 11 to 14 V and below 3 V
    E13-7 (WRNP) - Body ground
    LG - Body ground
    Seat belt warning light signal (Front passenger side)
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is fastened
    Below 1 V
    E13-8 (L) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is unfastened (Front driver side)
    Below 1 V
    E13-8 (L) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is fastened (Front driver side)
    9 to 14 V
    E14-9 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Always
    200 Ω or higher
    E14-10 (CANH) - Body ground
    R - Body ground
    CAN communication line
    Always
    200 Ω or higher
    If the result is not as specified, there may be a malfunction in the wire harness.


CENTER AIRBAG SENSOR ASSEMBLY

C109532E23


Terminal No.
Terminal Symbol
Destination
E29-21
IG2
IGN fuse
E29-25
E1
Ground
K1-16
FSR+
Occupant Classification ECU
K1-24
FSR-
Occupant Classification ECU

OCCUPANT CLASSIFICATION ECU

H100909E12

  1. Disconnect the Q4 occupant classification ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q4-1 (+B) - Body ground
    W-R - Body ground
    Battery
    Always
    11 to 14 V
    Q4-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    Q4-7 (IG) - Body ground
    B-O - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1 V → 11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the occupant classification ECU connector.

  4. Measure the resistance of the wire harness side connector.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Q4-4 (FSR-) - Q4-3 (GND)
    B - W-B
    Center airbag sensor assembly communication line (-)
    Always
    Below 1 Ω
    Q4-5 (BGND) - Q4-3 (GND)
    GR - W-B
    Passenger side buckle switch ground line
    Always
    Below 1 Ω
    Q4-8 (FSR+) - Q4-4 (FSR-)
    W - B
    Center airbag sensor assembly communication line
    Ignition switch ON
    Pulse generation
    Q4-9 (BSW) - Q4-5 (BGND)
    L - GR
    Passenger side buckle switch line
    Buckle switch ON
    Buckle switch OFF
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.


MAIN BODY ECU (Driver Side J/B)

B136051E04


B136052E04

  1. Disconnect the 1A, 1B and 1H main body ECU (driver side J/B) connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1B-4 (BECU) Body ground
    W-R - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    1H-2 (GND1) - Body Ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1A-7 (GND2) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU (driver side J/B) connectors.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1F-8 (SIG) - Body ground
    B-R - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1V → 11 to 14V
    E6-13 (DBKL) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is unfastened (Front driver side)
    Below 1 V
    E6-13 (DBKL) - Body ground
    G-Y - Body ground
    Front seat inner belt signal (Front driver side)
    Ignition switch ON
    Front seat belt is fastened (Front driver side)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.