Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › BLOWER UNIT

BLOWER UNIT > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B133850E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


3. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    I102500E01
  1. Remove the caps from the service valves on the refrigerant line.

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    NOTICE:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.



    A070279E03
  1. Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape



  1. Fix the vinyl hose with tape.


    A307922E01


    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.



5. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY


    E148352
  1. Using a 8 mm (5/16 inch) wrench, remove the radio antenna pole sub-assembly by turning it counterclockwise.



6. REMOVE WINDSHIELD WIPER ARM COVER


    E127858E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 3 front wiper arm cover.



7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127859
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)

HINT:
Use the same procedure as for the LH side.



9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE FRONT FENDER SIDE PANEL UPPER LH


    B210065
  1. Disengage the 4 clips and remove the front fender side panel upper LH.

  1. Remove the 4 clips from front fender side panel upper LH.



11. REMOVE ANTENNA ORNAMENT


    E127861E01
  1. Pull out the antenna ornament vertically.



12. REMOVE FRONT FENDER SIDE PANEL UPPER RH


    B210064
  1. Disengage the 4 clips and remove the front fender side panel upper RH.

  1. Remove the 4 clips from the front fender side panel upper RH.



13. REMOVE COWL TOP VENTILATOR LOUVER ASSEMBLY


    E127863
  1. Disengage the 7 clips and remove the cowl top ventilator louver sub-assembly.



14. REMOVE COWL TOP VENTILATOR LOUVER RH


    E127864
  1. Disengage the clip and remove the hood to cowl top seal.

  1. Remove the 3 clips and the claw, and remove the cowl top ventilator louver RH.



15. REMOVE COWL TOP VENTILATOR LOUVER LH


    E127865
  1. Remove the 5 clips.

  1. Disengage the 7 claws and remove the cowl top ventilator louver LH.



16. DISCONNECT COOLER REFRIGERANT SUCTION PIPE A


I003839E04
  1. Install SST onto the piping clamp.

    SST
    09870-00015  

    HINT:
    Check the directions of the piping clamp and SST by referring to the illustration on the caution label.

  1. Push down SST and release the clamp lock.

    NOTICE:
    Do not deform the tube when pushing SST.

  1. Pull SST slightly, push the release lever, and then remove the piping clamp with SST.

  1. Disconnect the suction pipe.

    NOTICE:
    1. Do not use any tools when disconnecting the pipe.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.



17. DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
SST
09870-00025  

HINT:
Disconnection procedure of the liquid pipe is the same as for the suction pipe.



18. DISCONNECT HEATER WATER HOSE INLET


I102426
  1. Using pliers, grip the claw of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



19. DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


I102428
  1. Using pliers, grip the claw of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



20. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


21. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    C128195
  1. Using a thin-bladed screwdriver, remove steering wheel cover lower No.3.

    HINT:
    Tape up the screwdriver tip before use.



22. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    C128196
  1. Using a thin-bladed screwdriver, remove steering wheel cover lower No.2.

    HINT:
    Tape up the screwdriver tip before use.



23. REMOVE STEERING PAD


    C128197E01
  1. Using "Torx" socket wrench (T30), loosen the 2 "Torx" screws until the groove along the screw circumference catches on the screw case.



    C128193E01
  1. Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



24. REMOVE STEERING WHEEL ASSEMBLY


C133806E02
  1. Remove the steering wheel assembly set nut.

  1. Place matchmarks on the steering wheel assembly and main shaft assembly.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



25. REMOVE LOWER STEERING COLUMN COVER


C133807
  1. Remove the 3 screws.

  1. Disengage the 2 claws to remove the lower steering column cover.



26. REMOVE UPPER STEERING COLUMN COVER


C231841
  1. Disengage the claw and then remove the upper steering column cover.



27. REMOVE COMBINATION SWITCH ASSEMBLY


C133809
  1. Disconnect all connectors from the combination switch assembly.

  1. Remove the 3 screws.



28. REMOVE FRONT DOOR SCUFF PLATE RH


    B130597
  1. Disengage the 14 claws and remove the front door scuff plate.



29. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



30. REMOVE FRONT FLOOR FOOTREST


    B130586
  1. Disengage the 4 claws and remove the front floor footrest.



31. REMOVE FOOTREST CLIP


    B130587
  1. Remove the 2 footrest clips.



32. REMOVE COWL SIDE TRIM BOARD RH


    B130599
  1. Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.



33. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



34. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip LH.



35. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip RH.



36. REMOVE ASSIST GRIP PLUG


B175647E03

HINT:
Use the same procedure to remove all the assist grip plugs.

Text in Illustration 
*1
Protective Tape
*a
for RH Side
*b
for LH Side
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.



37. REMOVE ASSIST GRIP ASSEMBLY


B175648E03

HINT:
Use the same procedure to remove all the assist grips.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Remove the 2 screws and the assist grip.



38. REMOVE FRONT PILLAR GARNISH RH


    B267110
  1. Disengage the 2 clips and the guide and remove the front pillar garnish.



39. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.



40. REMOVE INSTRUMENT PANEL GARNISH LH


    B133886
  1. Remove screw <H>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.



41. REMOVE INSTRUMENT PANEL GARNISH RH


    B133887
  1. Remove screw <H>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.



42. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B133888
  1. Remove the 2 <H> screws.

  1. Disengage the 4 clips and remove the integration control panel assembly.

  1. Disconnect the 3 connectors.



43. REMOVE RADIO RECEIVER ASSEMBLY


    E221529
  1. Remove the 4 bolts and the radio receiver.

  1. Disconnect the connectors.



44. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B133898E02
  1. Disengage the 2 A claws and 2 B claws.

  1. Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 C claws and remove the parking brake hole cover.



45. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)


    B133893
  1. Remove the shift lever knob.



46. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)


    B133895
  1. Remove the shift lever knob.



47. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B133897
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and 3 claws and remove the console upper rear panel.



48. REMOVE BOX BOTTOM MAT


    B133899
  1. Remove the box bottom mat.



49. REMOVE FRONT CONSOLE BOX


    B133851
  1. Remove the 4 <D> bolts.

  1. Disengage the 5 claws and remove the console box.



50. REMOVE CONSOLE UPPER PANEL NO. 1 GARNISH


B133900E01
  1. Disengage claw A and the clip.

  1. Slide the console upper panel garnish toward the rear of the vehicle, disengage the claw B and remove the console upper panel garnish.



51. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B133852
  1. Remove the 2 clips and 2 <F> bolts.

  1. Disengage the 3 clips and 2 claws and remove the instrument lower cover.



52. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B133853
  1. Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.



53. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B133859
  1. Disengage the 3 claws and separate the hood lock control lever.



54. REMOVE INSTRUMENT PANEL FINISH PLATE


E149562E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.



55. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B133860
  1. Remove the 2 <F> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.

  1. Disconnect the connector.



56. REMOVE LOWER INSTRUMENT PANEL LH


    B133864
  1. Remove the 4 <F> bolts and remove the lower instrument panel.



57. REMOVE INSTRUMENT CLUSTER FINISH PANEL


    B133861
  1. Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.

  1. Disconnect the connectors.



58. REMOVE COMBINATION METER ASSEMBLY


    B133862
  1. Remove the 4 screws.



    B133863
  1. Disconnect the 2 connectors and clamp and remove the combination meter.



59. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B133854E01
  1. Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.



    B133855
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



60. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B133857
  1. Remove screw <A>.

  1. Disengage the 2 clips and claw and remove the instrument panel lower finish panel.

  1. Separate the connectors from the instrument panel lower finish panel.



61. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B287551E01
  1. Apply protective tape, as shown in the illustration.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel hole cover.



    B287549
  1. Remove the bolt <F> and clip.

  1. Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.



62. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B133865
  1. Disengage the 4 clips and claw and remove the instrument panel speaker panel.



63. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure as for the RH side.



64. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    E218763
  1. Disengage the clamp.

  1. Remove the 2 bolts and the front speaker bracket.



65. REMOVE ASSIST GRIP RETAINER RH


B133881
  1. Remove the 2 bolts and remove the assist grip retainer.



66. REMOVE ASSIST GRIP RETAINER LH

HINT:
Use the same procedure as for the RH side.



67. DISCONNECT PASSENGER AIRBAG CONNECTOR


B133890E02
  1. Slide the slider and disconnect the passenger airbag connector.



68. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Disengage the clamps and disconnect the connectors.



  1. Remove the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G> and remove the instrument panel.


    B133866E01



69. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    B133889
  1. Disengage the 3 claws and remove the instrument panel finish panel end.



70. REMOVE NO. 1 HEATER TO REGISTER DUCT


    I102430
  1. Remove the screw and remove the heater to register duct.



71. REMOVE NO. 2 HEATER TO REGISTER DUCT


    I102431
  1. Remove the screw and remove the heater to register duct.



72. REMOVE REAR NO. 1 AIR DUCT


    I102433
  1. Disengage the 6 claws and 3 clamps and remove the rear air duct.



73. REMOVE REAR NO. 2 AIR DUCT


    I102432
  1. Disengage the 6 claws and 3 clamps and remove the rear air duct.



74. REMOVE NO. 1 AIR DUCT


    I102434
  1. Disengage the 3 claws and remove the air duct.



75. REMOVE NO. 2 AIR DUCT


    I102435
  1. Disengage the 3 claws and remove the air duct.



76. REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET


I102436
  1. for LH side:

    1. Remove the bolt and nut and remove the instrument panel brace mounting bracket.



    I102437
  1. for RH side:

    1. Remove the bolt and nut and remove the instrument panel brace mounting bracket.



77. REMOVE ECM


    A226613
  1. Disconnect the 6 connectors.

  1. Remove the 3 nuts and ECM.



78. REMOVE STEERING COLUMN HOLE COVER


F051329E01
  1. Disengage the 4 clips and remove the steering column hole cover.



79. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY


I102502E01
  1. Remove the bolt and separate the steering shaft thrust stopper from the steering intermediate shaft assembly.

  1. Mark matchmarks on the steering column assembly and steering intermediate shaft.

  1. Pull the intermediate shaft assembly and steering shaft thrust stopper out of the steering column assembly.



80. REMOVE STEERING COLUMN ASSEMBLY


C133810E01
  1. Disconnect the connectors and wire harness clamps.

  1. Remove the 4 nuts, then remove the steering column assembly from the instrument panel reinforcement assembly.



81. REMOVE INSTRUMENT PANEL SIDE BRACKET


    I102438
  1. Remove the bolt and remove the instrument panel side bracket.



82. SEPARATE MAIN BODY ECU (DRIVER SIDE J/B)


    I102439
  1. Remove the 2 nuts and remove the driver side junction block.



83. REMOVE COOLER UNIT DRAIN HOSE


    I102468
  1. Disconnect the cooler unit drain hose.



84. REMOVE INSTRUMENT PANEL REINFORCEMENT


  1. Remove the 3 bolts and 5 nuts and disconnect the wire harness.


    I102440

  1. Disconnect the connectors.



  1. Disengage the clamps.


    I102441



  1. Remove the 5 bolts and the 2 nuts.


    I102442



  1. Remove the 2 caps and the 7 bolts.


    I102443

  1. Disengage the reinforcement hook of the air conditioning unit, and remove the reinforcement.

  1. Remove the air conditioning unit.



85. REMOVE BLOWER UNIT ASSEMBLY


    I102447
  1. Remove the 2 screws.

  1. Remove the blower unit as shown in the illustration.