Home › BODY ELECTRICAL › DOOR LOCK › KEY REMINDER WARNING SYSTEM

KEY REMINDER WARNING SYSTEM > Key Reminder Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC position. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.

WIRING DIAGRAM


B136073E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (D DOOR COURTESY SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body ECU:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side door courtesy switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-

OK:
When the driver side door is opened/closed, the display will change as shown above.



OK
Go to step 4
NG


2.INSPECT FRONT DOOR COURTESY SWITCH (DRIVER SIDE)


    E114552E01
  1. Remove the front door courtesy switch (driver side).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩor higher

  1. Reinstall the front door courtesy switch (driver side).



NG
REPLACE FRONT DOOR COURTESY SWITCH (DRIVER SIDE)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH (DRIVER SIDE) - MAIN BODY ECU)


    B136069E01
  1. Disconnect the J1 front door courtesy switch (driver side) connector.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J1-1 - E7-23 (DCTY)
    Below 1 Ω
    J1-1 or E7-23 (DCTY) - Body ground
    10 kΩor higher

  1. Reconnect the courtesy switch and main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING TECHSTREAM (KEY UNLOCK WARNING SW)
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body ECU:

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal / ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:
When the ignition key is operated, the display changes as shown above.



OK
Go to step 7
NG


5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B062710E01
  1. Remove the unlock warning switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩor higher
    1 - 2
    Pushed
    Below 1 Ω

  1. Reinstall the unlock warning switch assembly.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


6.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)


    B136070E01
  1. Disconnect the E21 unlock warning switch assembly connector.

  1. Disconnect the E8 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E21-2 - E8-14 (KSW)
    Below 1 Ω
    E21-2 or E8-14 (KSW) - Body ground
    10 kΩor higher
    E21-1 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch and the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT MAIN BODY ECU


    B136071E01
  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-15 (KSWO) - Body ground
    Key is in ignition key cylinder
    Below 1 V
    E8-15 (KSWO) - Body ground
    No key is in ignition key cylinder
    10 to 14 V
    E8-11 (DCY2) - Body ground
    Driver side door is open
    Below 1 V
    E8-11 (DCY2) - Body ground
    Driver side door is closed
    10 to 14 V



NG
REPLACE MAIN BODY ECU
OK


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MAIN BODY ECU)
B136072E01
  1. Disconnect the E8 main body ECU connector.

  1. Disconnect the E13 combination meter assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E8-15 (KSWO) - E13-9 (KSW)
    Below 1 Ω
    E8-15 (KSWO) or E13-9 (KSW) - Body ground
    10 kΩor higher
    E8-11 (DCY2) - E13-29 (DOOR)
    Below 1 Ω
    E8-11 (DCY2) or E13-29 (DOOR) - Body ground
    10 kΩor higher

  1. Reconnect the main body ECU and combination meter assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY