Home › DRIVE LINE ยท DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY

FRONT DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


R013421E01
  1. Using SST and a press, press in the shaft bearing.

    SST
    09223-00010  

  1. Using a snap ring expander, install the snap ring.

    HINT:
    Install the snap ring securely.



2. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


C097022E03
  1. Install the shaft into the differential tube.

  1. Using needle nose pliers, install the snap ring.

    HINT:
    Install the snap ring securely.



3. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


F044351E02
  1. Coat the lip of a new oil seal with MP grease.

    Oil seal depth:
    4.8 to 5.8 mm (0.189 to 0.229 in.)

  1. Using SST and a plastic-faced hammer, tap in the oil seal.

    SST
    09223-15020  



4. INSTALL DIFFERENTIAL CLUTCH HUB


G023138E01
  1. Install the clutch hub onto the side gear inter shaft.

  1. Using snap ring pliers, install the snap ring.

    HINT:
    Install the snap ring securely.

    NOTICE:
    Install the differential clutch hub in the correct direction.



5. INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING


SA00355E01
  1. Using SST and a press, press in 2 new bearings.

    SST
    09950-60010   (09951-00380)

    Needle roller bearing depth:
    1.4 to 2.0 mm (0.055 to 0.079 in.)



6. ASSEMBLE DIFFERENTIAL CASE


FA01121E01
  1. Install the 2 thrust washers onto the 2 side gears.

    HINT:
    Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.

    Thrust washer thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    1.48 to 1.52 (0.0583 to 0.0598)
    1.73 to 1.77 (0.0681 to 0.0697)
    1.53 to 1.57 (0.0602 to 0.0618)
    1.78 to 1.82 (0.0701 to 0.0717)
    1.58 to 1.62 (0.0622 to 0.0638)
    1.83 to 1.87 (0.0720 to 0.0736)
    1.63 to 1.67 (0.0642 to 0.0657)
    1.88 to 1.92 (0.0740 to 0.0756)
    1.68 to 1.72 (0.0661 to 0.0677)
    -



    B084283E02
  1. Install the 2 side gears, 2 pinion gears, 2 side gear thrust washers, 2 pinion thrust washers and pinion shaft into the differential case.

    HINT:
    Align the holes of the differential case and pinion shaft.



    F014547E01
  1. Measure the side gear backlash.

    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

      Backlash:
      0.15 mm (0.0059 in.) or less

      1. If the backlash is not as specified, install 2 side gear thrust washers with different thicknesses.



    FA01124E01
  1. Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.

  1. Stake the differential case.



7. INSTALL DIFFERENTIAL RING GEAR


SA02160E01
  1. Clean the contact surface of the differential case and ring gear.

  1. Heat the ring gear in water that is approximately 100 °C (212 °F).

  1. Carefully remove the ring gear from the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case.



    C113177E01
  1. Align the matchmarks on the ring gear with those of the differential case.

  1. After the ring gear cools down, apply thread lock adhesive to the 10 set bolts and install them.

    Thread lock:
    THREE BOND 1360K or the equivalent.

    Torque:
    115 N*m{ 1,173 kgf*cm , 85 ft.*lbf }



8. INSTALL FRONT DIFFERENTIAL CASE BEARING


F044352E01
  1. Using SST and a press, press the bearing into the differential case.

    SST
    09950-60010   (09951-00520, 09951-00610)
    09950-70010   (09951-07150)



9. INSTALL FRONT DIFFERENTIAL CASE BEARING


R013375E01

HINT:
When replacing the 3 differential case bearings, fit the 2 thinnest new washers onto each bearing. When reusing the bearings, fit the new washers into the same places they were removed from.

  1. Using SST and a press, press the case bearing (outer race) into the differential case bearing retainer.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



    R013376E01
  1. Using SST and a press, press the case bearing (outer) into the differential carrier.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



10. INSTALL BEARING OUTER RACE


R013281E01
  1. Using SST, install the outer race front.

    SST
    09950-00020   (09951-00890, 09951-00680)

  1. Using a brass bar and hammer, tap in the oil storage ring.

  1. Using SST, install the outer race rear.

    SST
    09950-00020   (09951-00890, 09951-00680)



11. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


SA03102E01
  1. Install the washer onto the drive pinion.

    HINT:
    First fit a washer that has the same thickness as the removed washer. After checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.

  1. Using SST and a press, press the front bearing onto the drive pinion.

    SST
    09506-30012  



12. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


C028218E01
  1. Install the drive pinion and oil slinger.

    HINT:
    Assemble the spacer and oil seal after adjusting the gear contact pattern.



    R011163E03
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    SA02347E01
  1. Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the flange in place, tighten the nut.

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten it.
    1. Apply hypoid gear oil to the nut.



    SA02352E01
  1. Using a torque wrench, measure the preload.

    Preload (at starting):
    Item
    Specified Condition
    New bearing
    0.98 to 1.57 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)
    Used bearing
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the bearing forward and backward several times before measuring.



13. INSTALL DIFFERENTIAL CASE ASSEMBLY


14. ADJUST DIFFERENTIAL RING GEAR BACKLASH
  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    R012683E02
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Backlash:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

    1. If the backlash is not as specified, adjust it by either increasing or decreasing the number of washers on both sides equally.

      HINT:
      There should be no clearance between the plate washer and case. Make sure that the ring gear has backlash.


      Washer thickness:

      Thickness mm (in.)
      Thickness mm (in.)
      Thickness mm (in.)
      1.57 to 1.59 (0.0618 to 0.0626)
      1.75 to 1.77 (0.0689 to 0.0697)
      2.03 to 2.05 (0.0791 to 0.0807)
      1.59 to 1.61 (0.0626 to 0.0634)
      1.77 to 1.79 (0.0697 to 0.0705)
      2.05 to 2.07 (0.0807 to 0.0815)
      1.61 to 1.63 (0.0634 to 0.0642)
      1.79 to 1.81 (0.0705 to 0.0713)
      2.07 to 2.09 (0.0815 to 0.0822)
      1.63 to 1.65 (0.0642 to 0.0650)
      1.81 to 1.83 (0.0713 to 0.0720)
      2.09 to 2.11 (0.0822 to 0.0830)
      1.65 to 1.67 (0.0650 to 0.0657)
      1.83 to 1.85 (0.0720 to 0.0728)
      2.11 to 2.13 (0.0830 to 0.0839)
      1.67 to 1.69 (0.0657 to 0.0665)
      1.85 to 1.87 (0.0728 to 0.0736)
      2.13 to 2.15 (0.0839 to 0.0846)
      1.69 to 1.71 (0.0665 to 0.0673)
      1.87 to 1.89 (0.0736 to 0.0744)
      2.15 to 2.17 (0.0846 to 0.0854)
      1.71 to 1.73 (0.0673 to 0.0681)
      1.89 to 2.01 (0.0744 to 0.0791)
      -
      1.73 to 1.75 (0.0681 to 0.0689)
      2.01 to 2.03 (0.0791 to 0.0799)
      -



15. INSPECT TOTAL PRELOAD


C003092E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    HINT:
    Bolts without torque specifications are shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.



16. ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
  1. Remove the differential case bearing retainer and differential case.



    R013220E01
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with prussian blue.

  1. Install the differential case and differential case bearing retainer.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.

  1. Remove the differential case bearing retainer and differential case.



  1. Inspect the tooth contact pattern.


    C113178E02



    ZK01912E02
  1. If the teeth are not contacting properly, use the following chart to select an appropriate washer.

    Washer thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.69 to 1.71 (0.0665 to 0.0673)
    1.93 to 1.95 (0.0760 to 0.0768)
    2.17 to 2.19 (0.0854 to 0.0862)
    1.72 to 1.74 (0.0677 to 0.0685)
    1.96 to 1.98 (0.0772 to 0.0780)
    2.20 to 2.22 (0.0866 to 0.0874)
    1.75 to 1.77 (0.0689 to 0.0697)
    1.99 to 2.01 (0.0783 to 0.0791)
    2.23 to 2.25 (0.0878 to 0.0886)
    1.78 to 1.80 (0.0700 to 0.0709)
    2.02 to 2.04 (0.0795 to 0.0803)
    2.26 to 2.28 (0.0890 to 0.0898)
    1.81 to 1.83 (0.0713 to 0.0720)
    2.05 to 2.07 (0.0807 to 0.0815)
    2.29 to 2.31 (0.0902 to 0.0909)
    1.84 to 1.86 (0.0724 to 0.0732)
    2.08 to 2.10 (0.0819 to 0.0827)
    2.32 to 2.34 (0.0913 to 0.0921)
    1.87 to 1.89 (0.0736 to 0.0744)
    2.11 to 2.13 (0.0831 to 0.0839)
    -
    1.90 to 1.92 (0.0748 to 0.0756)
    2.14 to 2.16 (0.0843 to 0.0850)
    -



17. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT


F044346E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  



    SA02349E03
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021  



18. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


B087869E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



19. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


20. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


Z000641E01
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  

  1. Remove the bearing spacer.



21. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


C093601E01
  1. Install a new bearing spacer onto the drive pinion.



22. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


C028218E02


23. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


24. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


R013417E01
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-22010  

    Oil seal depth:
    3.9 to 4.8 mm (0.154 to 0.189 in.)



25. INSTALL FRONT DIFFERENTIAL DUST DEFLECTOR


B053734E01
  1. Using a steel plate and a press, press in a new dust deflector.

    NOTICE:
    Do not damage the dust deflector.



26. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F044356E01
  1. Place the companion flange on the drive pinion.

  1. Coat the threads of a new nut with hypoid gear oil.

  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    SA02351E03
  1. Using SST to hold the companion flange in place, tighten the nut to the correct torque.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less



27. INSTALL DIFFERENTIAL SIDE BEARING RETAINER


R013200E01
  1. Remove any old FIPG material from the side bearing retainer.

    NOTICE:
    Do not drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean residual FIPG material from the contact surface using gasoline or alcohol.

  1. Apply FIPG to the side bearing retainer, as shown.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    HINT:
    Install the side bearing retainer within 10 minutes of applying FIPG.

  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



28. INSPECT DRIVE PINION PRELOAD


SA02352E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Item
    Specified Condition
    New bearing
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 14 in.*lbf)
    Used bearing
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    1. If the preload is greater than the maximum, replace the bearing spacer.
    1. If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less

    1. If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

      HINT:
      Do not loosen the pinion nut to reduce the preload.



29. INSPECT TOTAL PRELOAD


SA02352E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Torque:
    Total preload (at starting):
    0.22 to 0.88 N*m{ 6 to 9 kgf*cm , 1.9 to 8.8 in.*lbf } drive pinion preload plus

    HINT:
    Bolts without torque specifications are shown in the service data (Click here).

    1. If necessary, disassemble and inspect the differential.



30. INSPECT DIFFERENTIAL RING GEAR BACKLASH


R012683E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Backlash:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload.



31. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F001237E03
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.0039 in.)
    Lateral runout
    0.10 mm (0.0039 in.)

    1. If the runout is greater than the maximum, replace the companion flange.



32. STAKE DRIVE PINION COMPANION FLANGE NUT


ZK07449E01
  1. Using a chisel and hammer, stake the drive pinion nut.



33. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


G021964E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a plastic-faced hammer, tap in the oil seal until its surface is flush with the differential carrier end.

    SST
    09608-32010  

    Oil seal depth:
    -0.45 to 0.45 mm (-0.018 to 0.018 in.)



34. INSTALL FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR


G023145E01
  1. Using a brass bar and hammer, tap in the side bearing retainer deflector.

    NOTICE:
    Install the side bearing retainer deflector in the correct direction.



35. INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


G023139E01
  1. Install a new snap ring onto the side gear inter shaft.

  1. Using a plastic-faced hammer, tap the side gear inter shaft into the differential case.

  1. Check that there is 2 to 3 mm (0.08 to 0.12 in.) of axial play.

  1. Check that the side gear inter shaft cannot be completely pulled out by hand.



36. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY


F044357E01
  1. Remove any old FIPG material from the contact surfaces of the differential and clutch case.

    NOTICE:
    Do not drop oil on the contact surfaces of the differential and clutch case.

  1. Clean residual FIPG material from the contact surface using gasoline or alcohol.

  1. Apply FIPG to the differential as shown.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    HINT:
    Install the differential tube within 10 minutes of applying FIPG.

  1. Install the differential tube onto the differential.



    G023134E01
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 or 3 threads of each bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. Install the 4 bolts.

    Torque:
    110 N*m{ 1,120 kgf*cm , 81 ft.*lbf }



37. INSTALL AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR


G023140E01
  1. Remove any FIPG material from the contact surface of the differential and clutch case. Also, do not drop oil on the contact surfaces.

  1. Clean residual FIPG material from the contact surfaces using gasoline or alcohol.

  1. Apply FIPG to the differential tube as shown.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    HINT:
    Install the actuator within 10 minutes of applying FIPG.



    G023143E01
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Install the actuator onto the differential tube.

  1. Apply adhesive to 2 or 3 threads of each bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. Install the 4 bolts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }