Home › DRIVE LINE ยท DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


C216539


2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F001237E18
Text in Illustration 
*a
Vertical Runout
*b
Lateral Runout
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.14 mm (0.0055 in.)
    Lateral runout
    0.14 mm (0.0055 in.)

    1. If the runout is greater than the maximum, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


C216538
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    1. If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C216537
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the side bearing preload.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092E01
  1. Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.88 to 1.98 N*m (9.0 to 20.2 kgf*cm, 7.8 to 17.5 in.*lbf)

    If necessary, disassemble and inspect the differential.



6. INSPECT TOTAL PRELOAD


C003092E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE REAR DRIVE PINION NUT


F044346E01
  1. Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

    SST
    09930-00010  



    SA02349E03
  1. Use SST to hold the companion flange.

    SST
    09330-00021  

  1. Using a socket wrench (30 mm), remove the rear drive pinion nut.



8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


B087869E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



9. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E02
  1. Using SST, remove the rear differential carrier oil seal from the differential carrier.

    SST
    09308-10010  



10. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


Z000641E01
  1. Using SST, remove the rear drive pinion front tapered roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



12. REMOVE DIFFERENTIAL CASE ASSEMBLY


C216540E01
Text in Illustration 
*1
Matchmark
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.



    C216541
  1. Using a screwdriver and hammer, remove the 2 plate washers.

    HINT:
    Measure the plate washer thickness and note it down.



    C216542
  1. Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races to show the location for reassembly.



13. REMOVE DIFFERENTIAL DRIVE PINION


    C030540
  1. Remove the drive pinion and bearing spacer from the differential carrier.



14. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E01
  1. Using SST and a press, press out the roller bearing (inner) from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.



15. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F044358E01
  1. Using SST, remove the roller bearing (outer) from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and hammer, tap out the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.



16. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C216543E01
  1. Using SST, tap out the rear tapered roller bearing (outer) from the carrier.

    SST
    09308-00010  

    HINT:
    If the bearing is damaged during removal, replace it.



17. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


18. REMOVE DIFFERENTIAL RING GEAR


C216547
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 12 ring gear set bolts.



    C014054E02
  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



19. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


C216544
  1. Install the rear differential case bearing onto the differential case.

  1. Install the differential case onto the differential carrier.

  1. Install the 2 plate washers onto the differential carrier with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.



20. REMOVE REAR DIFFERENTIAL CASE BEARING


F040345E02
  1. Using SST, remove the 2 bearings from the differential case.

    SST
    09950-40011   (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00500, 09951-00650, 09952-06010)

    HINT:
    Do not remove the case bearing unless replacing the differential case.



21. DISASSEMBLE DIFFERENTIAL CASE


C216546
  1. Place matchmarks on the LH and RH cases.

  1. Remove the 8 bolts.

    NOTICE:
    Loosen the bolts gradually, always skipping to a diagonally opposite bolt.



    ZK09094
  1. Using a plastic hammer, separate the LH and RH cases.



    C090324E02
  1. Remove the following parts from the differential case.
    A
    Side gear
    B
    Side gear thrust washer
    C
    Spider
    D
    Pinion gear
    E
    Pinion gear thrust washer