OCCUPANT CLASSIFICATION SYSTEM > TERMINALS OF ECU |
| OCCUPANT CLASSIFICATION ECU |

| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specification |
| +B (Q4-1) - GND (Q4-3) | W-R - W-B | Power source (ECU-B Fuse) | Always | 11 to 14 V |
| DIA (Q4-2) - GND (Q4-3) | R-Y - W-B | Diagnosis (DLC3) | Ignition switch on | Pulse generation |
| GND (Q4-3) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| FSR- (Q4-4) - GND (Q4-3) | B - W-B | Center airbag sensor assembly communication line (-) | Always | Below 1 Ω |
| BGND (Q4-5) - GND (Q4-3) | GR - W-B | Passenger side buckle switch ground line | Always | Below 1 Ω |
| IG (Q4-7) - GND (Q4-3) | B-O - W-B | Power source (IG2 Fuse) | Ignition switch on | 11 to 14 V |
| FSR+ (Q4-8) - FSR- (Q4-4) | W - B | Center airbag sensor assembly communication line | Ignition switch on | Pulse generation |
| BSW (Q4-9) - BGND (Q4-5) | L - GR | Passenger side buckle switch line | Buckle switch ON Buckle switch OFF | Pulse generation |
| SGD1 (Q5-1) - GND (Q4-3) | G - W-B | Occupant classification sensor front LH ground line | Always | Below 1 Ω |
| SGD2 (Q5-2) - GND (Q4-3) | O - W-B | Occupant classification sensor front RH ground line | Always | Below 1 Ω |
| SGD3 (Q5-3) - GND (Q4-3) | W - W-B | Occupant classification sensor rear LH ground line | Always | Below 1 Ω |
| SGD4 (Q5-4) - GND (Q4-3) | BR - W-B | Occupant classification sensor rear RH ground line | Always | Below 1 Ω |
| SVC1 (Q5-11) - SGD1 (Q5-1) | R - G | Occupant classification sensor front LH power supply line | Ignition switch on, a load is applied to occupant classification sensor front LH | 4.5 to 5.1 V |
| SVC2 (Q5-12) - SGD2 (Q5-2) | W - O | Occupant classification sensor front RH power supply line | Ignition switch on, a load is applied to occupant classification sensor front RH | 4.5 to 5.1 V |
| SVC3 (Q5-5) - SGD3 (Q5-3) | GR - W | Occupant classification sensor rear LH power supply line | Ignition switch on, a load is applied to occupant classification sensor rear LH | 4.5 to 5.1 V |
| SVC4 (Q5-6) - SGD4 (Q5-4) | V - BR | Occupant classification sensor rear RH power supply line | Ignition switch on, a load is applied to occupant classification sensor rear RH | 4.5 to 5.1 V |
| SIG1 (Q5-7) - SGD1 (Q5-1) | BR - G | Occupant classification sensor front LH signal line | Ignition switch on, a load is applied to occupant classification sensor front LH | 0.2 to 4.7 V |
| SIG2 (Q5-8) - SGD2 (Q5-2) | L - O | Occupant classification sensor front RH signal line | Ignition switch on, a load is applied to occupant classification sensor front RH | 0.2 to 4.7 V |
| SIG3 (Q5-9) - SGD3 (Q5-3) | Y - W | Occupant classification sensor rear LH signal line | Ignition switch on, a load is applied to occupant classification sensor rear LH | 0.2 to 4.7 V |
| SIG4 (Q5-10) - SGD4 (Q5-4) | B - BR | Occupant classification sensor rear RH signal line | Ignition switch on, a load is applied to occupant classification sensor rear RH | 0.2 to 4.7 V |