ENGINE IMMOBILISER SYSTEM > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
When adding master keys or sub keys (Additional registration):
Register the key code (immobiliser code) in the transponder key ECU assembly.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "B" |
When replacing the transponder key ECU assembly (New registration):
Register the key code (immobiliser code) in the new transponder key ECU assembly.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "A" |
Register the ECU communication ID between the new transponder key ECU assembly and the ECM.
| Target ECU | Refer to |
| ECM | Procedure "E" |
When replacing the ECM:
Register the ECU communication ID between the transponder key ECU assembly and the new ECM.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "F" |
When replacing the transponder key ECU assembly and the ECM:
Register the key codes (immobiliser codes) in the new transponder key ECU assembly.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "A" |
Register the ECU communication ID between the new transponder key ECU assembly and the new ECM.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "F" |
When erasing key codes:
Erasing all of the key codes except the master key.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "C" |
Erasing all of the key codes.
| Target ECU | Refer to |
| Transponder key ECU assembly | Procedure "D" |
| 2. KEY REGISTRATION |
New key code registration (Procedure "A"):
| Procedure | Security Indicator Light Condition |
| 1. Start | Blinking
|
| 2. Insert the master key into the ignition key cylinder. | ON |
| 3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration
| OFF for 1 second and then ON |
| 4. Remove the key and then select Next on the Techstream. | ON |
| 5. Insert the master key to be registered and then select Next on the Techstream. | OFF for 1 second and then ON |
| 6. Remove the key and then select Next on the Techstream. | ON |
| 7. Insert the sub-key to be registered and then select Next on the Techstream. | OFF for 1 second and then ON for 0.5 seconds and then OFF |
| 8. Remove the key. | Blinking |
| 9. End (Procedure "E") | |

Finish the automatic key code registration mode. The automatic key code registration mode can be forced to end when at least 1 key code (immobiliser code) for the master key has been registered.
| 3. REGISTRATION OF ADDITIONAL KEY |
Additional registration (Procedure "B"):
| Procedure | Time to Complete Operation | Security Indicator Light Condition |
| 1. Start | - | Blinking
|
| 2. Insert the already registered master key into the ignition key cylinder and turn the ignition switch to ON. | - | OFF |
| 3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Key Registration
| Within 120 sec. | ON |
| 4. Remove the master key. | Within 20 sec.
| ON |
| 5. Insert the key to be registered in the ignition key cylinder. | Within 10 sec. | Blinking |
6. Wait for 60 sec. after the key is registered.
| - | OFF |
| 7. Remove the key. | - | Blinking |
| 8. End | ||
| 4. ERASURE OF KEY CODE |
Key code erasure (Procedure "C"):
| Procedure | Time to Complete Operation | Security Indicator Light Condition |
| 1. Start | - | Blinking
|
| 2. Insert the already registered master key in the ignition key cylinder and turn the ignition switch to ON. | - | OFF |
| 3. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure
| Within 120 sec. | ON for 1 sec. then OFF |
| 4. Remove the master key. | Within 10 sec.
| ON |
| 5. End | ||
All key code erasure (Procedure "D"):
| Procedure | Time to Complete Operation | Security Indicator Light Condition |
| 1. Start | - | Blinking |
| 2. Insert previously registered master key or unregistered key into ignition key cylinder and turn ignition switch to ON. | Within 10 min. | ON or OFF |
| 3. Using TIS, confirm that user and vehicle match. | ||
| 4. Techstream operation Enter the following menus: Body Electrical / Immobiliser / Utility / Transponder Code Erasure
| Within 15 min. | ON for 1 sec. then OFF |
| 5. Completion of erasure of all key codes is displayed. | Within 10 sec.
| ON |
| 6. End | ||
| 5. ECU COMMUNICATION ID REGISTRATION |
ECU communication ID registration (Procedure "E"):
Using SST, connect terminals TC and CG of the DLC3.

Turn the ignition switch to ON and leave the vehicle as is for 30 minutes.
Check that the engine starts.
ECU communication ID registration (Procedure "F"):
| Procedure | Security Indicator Light Condition |
| 1. Start | OFF |
| 2. Insert an already registered key into the ignition key cylinder. | |
| 3. Start the engine. | |
| 4. Check that the engine starts and stays on for more than 3 seconds. | |
| 5. End | |