Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



TELEVISION CAMERA ASSEMBLY


  1. Disconnect the c1 television camera assembly connector.


    E168282E02

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c1-3 (CGND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 V
    c1-4 (CB+) - c1-3 (CGND)
    B - BR
    Power source
    Ignition switch ON,
    shift lever in R
    5.5 to 7.05 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the c1 television camera assembly connector.

  4. Measure the waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c1-1 (CV-) - c1-2 (CV+)
    W - R
    Display signal
    Ignition switch ON,
    shift lever in R
    Pulse generation
    (See waveform)
    If the result is not as specified, the camera may have a malfunction.



  5. E119731E01
  6. Using an oscilloscope, check the waveform.
    Waveform (Reference) 
    Terminal Connection
    c1-1 (CV-) - c1-2 (CV+)
    Tester Range
    0.2 V/DIV., 50 μs/DIV.
    Vehicle Condition
    Ignition switch ON,
    shift lever in R


INNER REAR VIEW MIRROR ASSEMBLY


  1. Disconnect the R6 inner rear view mirror assembly connector.


    E168283E02

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R6-1 (IG) - R6-2 (E)
    Y-R - W-B
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    R6-2 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    R6-3 (REV) - R6-2 (E)
    R-Y - W-B
    Reverse signal
    Ignition switch ON,
    shift lever not in R
    Below 1 V
    Ignition switch ON,
    shift lever in R
    11 to 14 V
    R6-6 (CV-) - R6-2 (E)
    W - W-B
    Signal ground
    Always
    Below 1 V
    R6-10 (BCTY) - Body ground
    W - Body ground
    Back door courtesy switch signal
    Back door is open
    Below 1 Ω
    Back door is closed
    10 kΩ or higher
    R6-13 (CGND) - Body ground
    Shielded - Body ground
    Television camera ground (Shielded)
    Always
    Below 1 V
    R6-14 (CB+) - R6-2 (E)
    B - W-B
    Power source to television camera
    Ignition switch ON,
    shift lever in R
    5.5 to 7.05 V

  3. Reconnect the R6 inner rear view mirror assembly connector.

  4. Measure the waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R6-7 (CV+) - R6-6 (CV-)
    R - W
    Television camera display signal (Input)
    Ignition switch ON,
    shift lever in R
    Pulse generation
    (See waveform)



  5. E119731E06
  6. Using an oscilloscope, check the waveform.
    Waveform (Reference) 
    Terminal Connection
    R6-7 (CV+) - R6-6 (CV-)
    Tester Range
    0.2 V/DIV., 50 μs/DIV.
    Vehicle Condition
    Ignition switch ON,
    shift lever in R