Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE LOWER NO.3 STEERING WHEEL COVER


    C128195
  1. Using a thin-bladed screwdriver, remove steering wheel cover lower No.3.

    HINT:
    Tape up the screwdriver tip before use.



5. REMOVE LOWER NO.2 STEERING WHEEL COVER


    C128196
  1. Using a thin-bladed screwdriver, remove steering wheel cover lower No.2.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE STEERING PAD


    C128197E01
  1. Using "Torx" socket wrench (T30), loosen the 2 "Torx" screws until the groove along the screw circumference catches on the screw case.



    C128193E01
  1. Pull the steering pad out of the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



7. REMOVE STEERING WHEEL ASSEMBLY


C133806E02
  1. Remove the steering wheel assembly set nut.

  1. Place matchmarks on the steering wheel assembly and main shaft assembly.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



8. REMOVE LOWER STEERING COLUMN COVER


C133807
  1. Remove the 3 screws.

  1. Disengage the 2 claws to remove the lower steering column cover.



9. REMOVE UPPER STEERING COLUMN COVER


C231841
  1. Disengage the claw and then remove the upper steering column cover.



10. REMOVE COMBINATION SWITCH ASSEMBLY


C133809
  1. Disconnect all connectors from the combination switch assembly.

  1. Remove the 3 screws.



11. REMOVE NO.1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B133853
  1. Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.



12. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



13. REMOVE FRONT FLOOR FOOTREST


    B130586
  1. Disengage the 4 claws and remove the front floor footrest.



14. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



15. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.



16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B133860
  1. Remove the 2 <F> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.

  1. Disconnect the connector.



17. REMOVE LOWER INSTRUMENT PANEL LH


    B133864
  1. Remove the 4 <F> bolts and remove the lower instrument panel.



18. REMOVE NO.1 AIR DUCT


    I102434
  1. Disengage the 3 claws and remove the air duct.



19. REMOVE STEERING COLUMN HOLE COVER


F051329E01
  1. Disengage the 4 clips and remove the steering column hole cover.



20. REMOVE FRONT WHEEL LH


21. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and the No. 1 engine under cover sub-assembly.



22. REMOVE NO.2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


F043317E01
  1. Mark matchmarks on the power steering gear assembly and No. 2 steering intermediate shaft.

  1. Remove bolt C and the No. 2 steering intermediate shaft from the power steering gear assembly.



23. REMOVE STEERING SLIDING YOKE
  1. Mark matchmarks on the steering sliding yoke, No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft assembly.

  1. Remove bolts A and B from the steering sliding yoke.

  1. Slide the steering sliding yoke up and separate it from the No. 2 steering intermediate shaft sub-assembly.

  1. Pull down the steering sliding yoke from the steering intermediate shaft assembly to remove.



24. REMOVE STEERING COLUMN ASSEMBLY


C133810E01
  1. Disconnect the connectors and wire harness clamps.

  1. Remove the 4 nuts, then remove the steering column assembly from the instrument panel reinforcement assembly.