STARTER > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Mount the starter in a vise between aluminum plates.
Perform a pull-in test.
Remove the nut, then disconnect the lead wire from terminal C.
![]() |
Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear extends.
| *1 | Terminal 50 |
| *2 | Terminal C |
![]() |
Perform a holding test.
| *1 | Terminal C |
Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.
If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.
![]() |
Inspect the clutch pinion gear return.
Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.
Perform an operation test without load.
Connect the lead wire to terminal C.
![]() |
Connect the battery and an ammeter to the starter as shown in the illustration.
| *1 | Terminal 50 |
| *2 | Terminal 30 |
Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.
| 2. INSPECT MAGNET STARTER SWITCH ASSEMBLY |
![]() |
Inspect the pull-in coil.
Measure the resistance according to the value(s) in the table below.
| *1 | Terminal 50 |
| *2 | Terminal C |
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Terminal C | Always | Below 1 Ω |
![]() |
Inspect the holding coil.
Measure the resistance according to the value(s) in the table below.
| *1 | Terminal 50 |
| *2 | Switch Body |
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Switch Body | Always | Below 2 Ω |
| 3. INSPECT BRUSH |
![]() |
Using a vernier caliper, measure the brush length.
| *a | Brush Holder Side: |
| *b | Starter Yoke Side: |
| *c | Length |
| 4. INSPECT STARTER BRUSH HOLDER ASSEMBLY |
Check the brush spring load.
![]() |
Take a pull scale reading immediately after the brush spring separates from the brush.
| *1 | Brush |
| *2 | Brush Spring |
![]() |
Inspect the insulation.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Positive (+) Brush Holder - Negative (-) Brush Holder | Always | 10 Ω or higher |
| 5. INSPECT STARTER YOKE ASSEMBLY |
Inspect the field coil for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Lead Wire - Brush | Always | Below 1 Ω |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Starter Yoke Body - Brush | Always | 10 kΩ or higher |
| 6. INSPECT STARTER ARMATURE ASSEMBLY |
Check the commutator for dirt and/or burns on the surface.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
![]() |
Inspect the commutator for an open circuit.
Measure the resistance according to the value(s) in the table below.
| *1 | Segment |
| Tester Connection | Condition | Specified Condition |
| Segment - Segment | Always | Below 1 Ω |
Inspect the commutator for a short circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| *1 | Segment |
| *2 | Coil Core |
| Tester Connection | Condition | Specified Condition |
| Segment - Coil Core | Always | 10 kΩ or higher |
![]() |
Check the commutator circle runout.
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
![]() |
Using a vernier caliper, measure the commutator diameter.
![]() |
Using a vernier caliper, measure the undercut depth of the commutator.
| 7. INSPECT STARTER CLUTCH SUB-ASSEMBLY |
![]() |
Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
![]() | Free |
![]() | Lock |
Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.