Home › DRIVE LINE ยท DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


C217291
  1. Fix the rear differential carrier assembly to the overattachment.



2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F001237E23
  1. Using a dial indicator, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    Runout
    Maximum
    Vertical runout
    0.14 mm (0.0055 in.)
    Lateral runout
    0.14 mm (0.0055 in.)

    If the runouts are not with the specifications, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


C217282
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C217283
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



6. INSPECT TOTAL PRELOAD


C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR


G020268
  1. Remove the 4 bolts and actuator from the differential carrier.

  1. Remove the O-ring.



8. REMOVE NO. 1 TRANSFER INDICATOR SWITCH


G020269
  1. Remove the indicator switch and gasket.



9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT


G020270
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and ball.



    G020271
  1. Using a 5 mm pin punch and hammer, remove the slotted pin.



    G020272
  1. Remove the 2 bolts from the shaft retainer.

  1. Using a plastic hammer, remove the shaft retainer.

  1. Remove the shift fork shaft.

  1. Remove the rear differential lock sleeve.



10. REMOVE REAR DRIVE PINION NUT


F044346E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of the SST with a grinder, etc.
    3. Completely loosen the staked part of the nut when removing.
    4. Do not damage the threads of the drive pinion.



    SA02349E06
  1. Using SST to hold the drive pinion companion flange, remove the nut.

    SST
    09330-00021  

  1. Using a socket wrench (30 mm), remove the rear drive pinion nut.



11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F052175E02
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



12. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



13. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

NOTICE:
Apply grease to the threads and tip of the SST center bolt before use.



14. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


Z000641E04
  1. Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09556-22010  

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



15. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


C217052
  1. Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.



16. REMOVE DIFFERENTIAL CASE ASSEMBLY


C217292E01
Text in Illustration 
*a
Matchmarks
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.



    C217285
  1. Remove the rear differential case sub-assembly and 2 case bearings from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races to show the locations for reassembly.



17. REMOVE DIFFERENTIAL DRIVE PINION


C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.



18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E02
  1. Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If either the drive pinion or ring gear is damaged, replace them as a set.



19. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.



20. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


21. REMOVE DIFFERENTIAL RING GEAR


C216547E02
Text in Illustration 
*a
Matchmarks
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 12 ring gear set bolts.



    C014054
  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case.



22. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F044358E02
  1. Using SST, remove the front tapered roller bearing from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and a hammer, remove the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during the removal, replace it.



23. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


G020277
  1. Install the rear differential case bearing onto the differential case.

  1. Install the differential case onto the differential carrier.

  1. Install the 2 bearing caps and 4 bolts onto the differential carrier.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Inspect the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.



24. REMOVE REAR DIFFERENTIAL CASE BEARING


F040345E03
  1. Using SST, remove the 2 rear differential case bearings from the differential case.

    SST
    09950-40011   (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00500, 09951-00650, 09952-06010)



25. DISASSEMBLE DIFFERENTIAL CASE


    F052178E05
  1. Place matchmarks on the LH and RH cases.
    Text in Illustration 
    *a
    Matchmarks

  1. Remove the 8 bolts.



    ZK09094
  1. Using a plastic hammer, separate the LH and RH cases.



    C090324E02
  1. Remove these parts from the differential case.
    A
    Side gear
    B
    Side gear thrust washer
    C
    Spider
    D
    Pinion gear
    E
    Pinion gear thrust washer