Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY


D029376E01


  1. Inspect the one-way clutch.

    1. Install SST in the inner race of the one-way clutch.

      SST
      09350-32014   (09351-32020)



    2. AT05437E01
    3. Press on the serrations of the stator with a finger and rotate it.
      Check if it rotates smoothly when turned clockwise and locks when turned counterclockwise.
      If the results are not as specified, clean the converter and recheck the one-way clutch. If the results still are not as specified, replace the converter.



    D025367E13
  1. Determine the condition of the torque converter clutch.

    1. Check that the following conditions are met:

      1. During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter clutch.
      2. The one-way clutch turns in one direction and locks in the other direction.
      3. The amount of powder in the ATF is not greater than the sample shown in the illustration.
      If the results are not as specified, replace the torque converter clutch assembly.

      HINT:
      The sample illustration shows approximately 0.25 liters (0.26 US qts, 0.22 Imp. qts) of the ATF taken from a removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter clutch thoroughly and drain the ATF with the torque converter facing up.



    C136397
  1. Clean and check the oil cooler and oil pipe line.

    1. If the torque converter clutch is inspected or the ATF is replaced, clean the oil cooler and oil pipe line.

      HINT:
      1. Apply compressed air of 196 kPa (2 kgf/cm2, 28 psi) into the inlet hose.
      2. If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.

    2. If the ATF is cloudy, inspect the oil cooler (radiator).



    D025368E05
  1. Prevent deformation of the torque converter clutch and damage to the oil pump gear.

    1. When any marks due to interference are found on the end of the bolt for the torque converter clutch and on the bottom of the bolt hole, replace the bolt and torque converter clutch.

    2. All of the bolts should be the same length.

    3. Make sure no spring washers are missing.



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch onto the automatic transmission.



    D025544E02
  1. Using a vernier caliper and a straightedge, measure dimension A, between the engine and the end surface of the drive plate, as shown in the illustration.

    Standard:
    A = 21.2 mm (0.835 in.)



    D025545E02
  1. Using a vernier caliper and a straightedge, measure dimension B shown in the illustration. Check that B is greater than A.

    Standard:
    B = A + 1.0 mm (0.0394 in.) or more



3. INSTALL REAR NO.1 ENGINE MOUNTING INSULATOR


C129543
  1. Install the engine mounting insulator rear onto the automatic transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


F051601E01
  1. Install the automatic transmission onto the engine with the 9 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf } for bolt A
    37 N*m{ 380 kgf*cm , 27 ft.*lbf } for bolt B



    F050354
  1. Install the 6 torque converter clutch mounting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black bolt and then the other 5 bolts.



5. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


F050353
  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }

  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



6. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


C129541
  1. Install the front suspension member bracket LH with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



7. INSTALL FRONT SUSPENSION MEMBER BRACKET RH


C129542
  1. Install the front suspension member bracket RH with the 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



8. INSTALL FLYWHEEL HOUSING SIDE COVER


F050352
  1. Install the flywheel housing side cover onto the cylinder block.



9. INSTALL STARTER ASSEMBLY
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the bolt and nut.

    Torque:
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for nut:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



10. CONNECT WIRE HARNESS


11. CONNECT CONNECTOR
  1. Connect the park/neutral position switch connector.

  1. Connect the transmission wire connector.

  1. Connect the 2 speed senor connectors.



12. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


F050351
  1. Install the transmission control cable bracket with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the transmission control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. INSTALL OIL COOLER TUBE
  1. Provisionally install the No. 1 oil cooler outlet tube.

  1. Provisionally install the No. 1 oil cooler inlet tube.



    F051602E01
  1. Install the 2 clamps and 3 bolts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf } for bolt A
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for bolt B



    F050350E01
  1. Using SST, tighten the No. 1 oil cooler outlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf } for use without SST
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for use with SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.

  1. Using SST, tighten the No. 1 oil cooler inlet tube.

    SST
    09023-12701  

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf } for use without SST
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for use with SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.



14. INSTALL NO.2 MANIFOLD STAY


F050356
  1. Install the No. 2 manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



15. INSTALL MANIFOLD STAY


F050360
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



16. INSTALL PROPELLER SHAFT ASSEMBLY


C098710E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C098700E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



17. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold RH.



    A128851
  1. Install the exhaust front pipe with 2 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



    A128852E01
  1. Install a new gasket onto the front exhaust pipe.

    1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the front exhaust pipe end.

      NOTICE:
      1. Make sure that the gasket is in the correct direction when installing.
      2. Do not reuse the removed gasket.
      3. Do not push in the gasket with the exhaust pipe when connecting it.



18. INSTALL NO. 2 EXHAUST FRONT PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold LH.

  1. Install a new gasket onto the No. 2 front exhaust pipe.



    A129938
  1. Install the front No. 2 exhaust pipe with 2 new nuts and 2 bolts and exhaust pipe support.

    Torque:
    Nut:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }
    Bolt:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



    A129939
  1. Install the exhaust pipe stopper bracket with the 2 bolts (for 4WD).

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



19. INSTALL OXYGEN SENSOR


20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



21. PERFORM INITIALIZATION
(Click here)


22. ADJUST AUTOMATIC TRANSMISSION FLUID
(Click here)


23. INSPECT SHIFT LEVER POSITION
  1. Check that the shift lever moves smoothly and appropriately from the P to the R position, only when the ignition switch is turned to ON and the brake pedal is depressed.

  1. When starting the engine, make sure that the vehicle moves forward when shifting the lever from the N to the D position and moves rearward when shifting the lever to the R position.



24. ADJUST SHIFT LEVER POSITION


    D028682E07
  1. Push the control shaft fully rearward.
    Text in Illustration 
    *a
    N Position

  1. Turn the control shaft lever 2 notches counterclockwise to the N position.

  1. Set the shift lever to the N position.



25. INSPECT FOR EXHAUST GAS LEAK

HINT:
Perform "Inspection After Repairs" after repairing or replacing the exhaust system (Click here).



26. INSTALL REAR ENGINE UNDER COVER ASSEMBLY


27. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY