Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


3. REMOVE REAR ENGINE UNDER COVER ASSEMBLY


4. DISCONNECT OXYGEN SENSOR


5. REMOVE NO. 2 EXHAUST FRONT PIPE ASSEMBLY


    A129939
  1. Remove the 2 bolts, then remove the exhaust pipe stopper bracket. (for 4WD)



    A129938
  1. Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the front No. 2 exhaust pipe.



6. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A128851
  1. Remove the 2 nuts, then remove the front exhaust pipe.

  1. Remove the front exhaust pipe gasket.



7. REMOVE PROPELLER SHAFT ASSEMBLY


C098700E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. Remove the propeller shaft assembly.



    C098710E01
  1. Insert SST into the extension housing to prevent oil leakage.

    SST
    09325-40010  



8. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



9. REMOVE MANIFOLD STAY


F050360
  1. Remove the 3 bolts and manifold stay.



10. REMOVE NO.2 MANIFOLD STAY


F050356
  1. Remove the 3 bolts and No. 2 manifold stay.



11. DISCONNECT OIL COOLER TUBE


F051602
  1. Remove the 3 bolts and 2 clamps.



    F050350E01
  1. Using SST, disconnect the No. 1 oil cooler inlet tube.

    SST
    09023-12701  

  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  



12. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


F050351
  1. Remove the nut and disconnect the transmission control cable.

  1. Remove the 2 bolts and disconnect the transmission control cable.



13. DISCONNECT CONNECTOR
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.



14. DISCONNECT WIRE HARNESS


15. REMOVE STARTER ASSEMBLY


    A222905
  1. Remove the bolt and ground wire.

  1. Disconnect the starter connector.

  1. Open the terminal cap.

  1. Remove the nut and bolt, and then disconnect the starter wire.



    A218197
  1. Remove the 2 bolts and starter.



16. REMOVE FLYWHEEL HOUSING SIDE COVER


F050352
  1. Remove the flywheel housing side cover from the cylinder block.



17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C112848
  1. Support the automatic transmission assembly with a transmission jack.



18. REMOVE FRONT SUSPENSION MEMBER BRACKET LH


C129541
  1. Remove the 4 bolts and front suspension member bracket LH.



19. REMOVE FRONT SUSPENSION MEMBER BRACKET RH


C129542
  1. Remove the 4 bolts and front suspension member bracket RH.



20. REMOVE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


F050353
  1. Remove the 4 bolts on the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.



21. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


F050354
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    F051601
  1. Remove the 9 bolts.

  1. Separate and remove the automatic transmission.



22. REMOVE REAR NO.1 ENGINE MOUNTING INSULATOR


C129543
  1. Remove the 4 bolts and engine mounting insulator rear from the automatic transmission.



23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY