AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSTALL TRANSFER ASSEMBLY |
Install the transfer onto the transmission.
Install the 2 clamps and 8 bolts.
| 2. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Inspect the one-way clutch.
Install SST in the inner race of the one-way clutch.
![]() |
Press on the serrations of the stator with a finger and rotate it.
Check if it rotates smoothly when turned clockwise and locks when turned counterclockwise.
If the results are not as specified, clean the converter and recheck the one-way clutch. If the results still are not as specified, replace the converter
![]() |
Determine the condition of the torque converter clutch.
Check that the following conditions are met:
Replace the ATF in the torque converter clutch.
If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter clutch thoroughly and drain the ATF with the torque converter facing up.
![]() |
Clean and check the oil cooler and oil pipe line.
If the torque converter clutch is inspected or the ATF is replaced, clean the oil cooler and oil pipe line.
If the ATF is cloudy, inspect the oil cooler (radiator).
![]() |
Prevent deformation of the torque converter clutch and damage to the oil pump gear.
When any marks due to interference are found on the end of the bolt for the torque converter clutch and on the bottom of the bolt hole, replace the bolt and torque converter clutch.
All of the bolts should be the same length.
Make sure no spring washers are missing.
| 3. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
Install the torque converter clutch onto the automatic transmission.
![]() |
Using calipers and a straight edge, measure dimension A, between the engine and the end surface of the drive plate, shown in the illustration.
![]() |
Using calipers and a straight edge, measure dimension B shown in the illustration. Check that B is greater than A.
| 4. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER |
![]() |
Install the automatic transmission onto the engine with the 9 bolts.
![]() |
Install the 6 torque converter clutch mounting bolts.
| 5. INSTALL FLYWHEEL HOUSING SIDE COVER |
![]() |
Install the flywheel housing side cover onto the cylinder block.
| 6. INSTALL STARTER ASSEMBLY |
Install the starter with the 2 bolts.
Connect the starter wire with the bolt and nut.
Close the terminal cap.
Connect the starter connector.
Connect the ground wire with the bolt.
| 7. CONNECT WIRE HARNESS |
| 8. CONNECT CONNECTOR |
Connect the 3 indicator switch connectors.
Connect the 2 speed sensor connectors.
Connect the transmission wire connector.
Connect the park/neutral position switch connector.
| 9. INSTALL REAR NO.1 ENGINE MOUNTING INSULATOR |
![]() |
Install the engine mounting insulator rear onto the automatic transmission with the 4 bolts.
| 10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.
Install the No. 3 frame crossmember sub-assembly with the 4 bolts.
| 11. INSTALL FRONT SUSPENSION MEMBER BRACKET LH |
![]() |
Install the front suspension member bracket LH with the 4 bolts.
| 12. INSTALL FRONT SUSPENSION MEMBER BRACKET RH |
![]() |
Install the front suspension member bracket RH with the 4 bolts.
| 13. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Install the transmission control cable bracket with the 2 bolts.
Connect the transmission control cable with the nut.
| 14. INSTALL OIL COOLER TUBE |
Provisionally install the No. 1 oil cooler outlet tube.
Provisionally install the No. 1 oil cooler inlet tube.
![]() |
Install the 2 clamps and 2 bolts.
![]() |
Using SST, tighten the No. 1 oil cooler outlet tube.
Using SST, tighten the No. 1 oil cooler inlet tube.
| 15. INSTALL NO. 2 MANIFOLD STAY |
![]() |
Install No. 2 manifold stay with the 3 bolts.
| 16. INSTALL MANIFOLD STAY |
![]() |
Install the manifold stay with the 3 bolts.
| 17. INSTALL PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.
![]() |
Align the matchmarks on the propeller shaft flange and transfer flange.
Install the propeller shaft assembly with the 4 nuts and 4 washers.
| 18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft assembly with the 4 nuts and 4 washers.
| 19. INSTALL PROPELLER SHAFT HEAT INSULATOR |
![]() |
Install the propeller shaft heat insulator with the 2 bolts.
| 20. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket onto the exhaust manifold RH.
![]() |
Install the exhaust front pipe with 2 new nuts.
![]() |
Install a new gasket onto the front exhaust pipe.
Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the front exhaust pipe end.
| 21. INSTALL NO. 2 EXHAUST FRONT PIPE ASSEMBLY |
Install a new gasket onto the exhaust manifold LH.
Install a new gasket onto the No. 2 front exhaust pipe.
![]() |
Install the front No. 2 exhaust pipe with 2 new nuts and 2 bolts and exhaust pipe support.
![]() |
Install the exhaust pipe stopper bracket with the 2 bolts (for 4WD).
| 22. CONNECT OXYGEN SENSOR |
| 23. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY |
![]() |
Install the transfer shift lever onto the shift lever retainer.
Using needle-nose pliers, install the snap ring.
| 24. INSTALL SHIFT LEVER BOOT ASSEMBLY |
![]() |
Install the shift lever boot with the 4 screws.
| 25. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer) |
| 26. INSTALL SHIFT LEVER ASSEMBLY (for Automatic Transmission) |
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 28. PERFORM INITIALIZATION |
| 29. ADJUST AUTOMATIC TRANSMISSION FLUID |
| 30. INSPECT SHIFT LEVER POSITION |
Check that the shift lever moves smoothly and appropriately from the P to the R position, only when the ignition switch is turned to ON and the brake pedal is depressed.
When starting the engine, make sure that the vehicle moves forward when shifting the lever from the N to the D position and moves rearward when shifting the lever to the R position.
| 31. ADJUST SHIFT LEVER POSITION |
![]() |
Push the control shaft fully rearward.
| *a | N Position |
Turn the control shaft lever 2 notches counterclockwise to the N position.
Set the shift lever to the N position.
| 32. INSPECT FOR EXHAUST GAS LEAK |
| 33. INSTALL REAR ENGINE UNDER COVER ASSEMBLY |
| 34. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |