Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE SHIFT LEVER ASSEMBLY (for Automatic Transmission)
(Click here)


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer)


3. REMOVE SHIFT LEVER BOOT ASSEMBLY


C135793
  1. Remove the 4 screws and shift lever boot.



4. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E04
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


6. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


7. REMOVE REAR ENGINE UNDER COVER ASSEMBLY


8. DISCONNECT OXYGEN SENSOR


9. REMOVE NO. 2 EXHAUST FRONT PIPE ASSEMBLY


    A129939
  1. Remove the 2 bolts, then remove the exhaust pipe stopper bracket. (for 4WD)



    A129938
  1. Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the front No. 2 exhaust pipe.



10. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A128851
  1. Remove the 2 nuts, then remove the front exhaust pipe.

  1. Remove the front exhaust pipe gasket.



11. REMOVE PROPELLER SHAFT HEAT INSULATOR


C133778
  1. Remove the 2 bolts and propeller shaft heat insulator.



12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C098708E04
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4bolts and 4 washers.



    C098709E03
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and the propeller shaft assembly.



13. REMOVE PROPELLER SHAFT ASSEMBLY


C098699E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and 4 washers.



    C098700E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and the propeller shaft assembly.



14. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



15. REMOVE MANIFOLD STAY


F050360
  1. Remove the 3 bolts and the manifold stay.



16. REMOVE NO. 2 MANIFOLD STAY


F050356
  1. Remove the 3 bolts and the No. 2 manifold stay.



17. DISCONNECT OIL COOLER TUBE


F051602
  1. Remove the 3 bolts and 2 clamps.



    F050350
  1. Using SST, disconnect the No. 1 oil cooler inlet tube.

    SST
    09023-12701  

  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  



18. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


F050351
  1. Remove the nut and disconnect the transmission control cable.

  1. Remove the 2 bolts and disconnect the transmission control cable.



19. SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER


C111233
  1. Support the automatic transmission assembly with a transmission jack.



20. REMOVE FRONT SUSPENSION MEMBER BRACKET LH


C129541
  1. Remove the 4 bolts and the front suspension member bracket LH.



21. REMOVE FRONT SUSPENSION MEMBER BRACKET RH


C129542
  1. Remove the 4 bolts and the front suspension member bracket RH.



22. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C133780
  1. Remove the 4 bolts on the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts, 4 bolts and the No. 3 frame crossmember sub-assembly.



23. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C133779
  1. Remove the 4 bolts and engine mounting insulator rear from the automatic transmission.



24. DISCONNECT CONNECTOR
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the 3 indicator switch connectors.



25. DISCONNECT WIRE HARNESS


26. REMOVE STARTER ASSEMBLY


    A222905
  1. Remove the bolt and ground wire.

  1. Disconnect the starter connector.

  1. Open the terminal cap.

  1. Remove the nut and bolt, and then disconnect the starter wire.



    A218197
  1. Remove the 2 bolts and starter.



27. REMOVE FLYWHEEL HOUSING SIDE COVER


F050352
  1. Remove the flywheel housing side cover from the cylinder block.



28. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER


F050354
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    F051601
  1. Remove the 9 bolts.

  1. Separate and remove the automatic transmission.



29. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


30. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.