Home › DRIVE LINE ยท DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL OUTBOARD JOINT BOOT


    C177228E02
  1. Wrap the spline of the outboard joint shaft with protective tape.
    Text in Illustration 
    *1
    Protective Tape

  1. Install new parts onto the outboard joint shaft in the following order.
    1.
    Front axle outboard joint boot No. 2 clamp
    2.
    Front axle outboard joint boot
    3.
    Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft and outboard joint boot with grease.

    Grease capacity:
    266 to 276 g (9.4 to 9.7 oz.)

  1. Install the outboard joint boot onto the outboard joint shaft groove.

    NOTICE:
    Keep the groove free of grease.



2. INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP
  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    F052126E04
  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    2.1 mm (0.083 in.) or less

  1. Remove SST.



    F052127E01
  1. Using SST, measure the clearance of the boot clamp as shown in the illustration.

    SST
    09240-00020  

    Clearance:
    2.1 mm (0.083 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.



3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    C081563E03
  1. Fix the outboard joint shaft in a vise between aluminum plates.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not overtighten the vise.

  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    1.3 mm (0.051 in.) or less

  1. Remove SST.



    C092627E01
  1. Using SST, measure the clearance of the boot clamp as shown in the illustration.

    SST
    09240-00020  

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.



4. INSTALL FRONT DRIVE SHAFT DUST COVER


    F041033E01
  1. Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.

    SST
    09527-10011  

    NOTICE:
    1. Install the dust cover in the correct orientation.
    2. Do not deform the dust cover.



5. INSTALL FRONT DRIVE INNER SHAFT INNER SHAFT SNAP RING
  1. Install a new snap ring.



6. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install new parts onto the outboard joint shaft in the following order.
    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front axle inboard joint boot No. 2 clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.



    C067417E30
  1. Align the matchmarks and install the tripod joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Beveled
    *b
    Matchmarks

    NOTICE:
    Place the beveled side of the tripod toward the inboard joint.

  1. Using a brass bar and hammer, install the tripod joint.

    NOTICE:
    1. Do not hit the roller portion.
    2. Keep the tripod joint free of foreign matter.



    G022501
  1. Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint with grease.

    Grease capacity:
    239 to 249 g (8.4 to 8.8 oz.)



    C054086E02
  1. Align the matchmarks and install the inboard joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Matchmarks



7. INSTALL INBOARD JOINT BOOT
  1. Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.

    NOTICE:
    Keep the grooves free of grease.



8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP


    D026925E18
  1. Fix the outboard joint shaft in a vise between aluminum plates.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not overtighten the vise.

  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.

  1. Remove SST.



    D026926
  1. Using SST, measure the clearance of the boot clamp as shown in the illustration.

    SST
    09240-00020  

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.



9. INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP


G022110E02
  1. Check whether the drive shaft dimensions are within the following specifications.
    Text in Illustration 
    *a
    Dimension A

    Dimension (A):
    577.5 mm (22.74 in.)

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C108292E14
  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    2.1 mm (0.082 in.) or less

  1. Remove SST.



    C086270E09
  1. Using SST, measure the clearance of the boot clamp as shown in the illustration.

    SST
    09240-00020  

    Clearance:
    2.1 mm (0.082 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.



10. INSPECT FRONT DRIVE SHAFT


W001721
  1. Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    NOTICE:
    Keep the drive shaft level while moving it.