Home › BRAKE › BRAKE › HYDRAULIC BRAKE BOOSTER

HYDRAULIC BRAKE BOOSTER > REASSEMBLY

for Preparation Click here



1. INSTALL BRAKE BOOSTER ACCUMULATOR ASSEMBLY


F051527
  1. Place the brake booster pump in a vise lined with a cloth.

  1. Install the brake booster accumulator pipe, compression spring and a new O-ring.

    NOTICE:
    Ensure that no foreign matter enters the pump.

  1. Install the brake booster accumulator onto the brake booster pump.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }



2. INSTALL PISTON
  1. Apply lithium soap base glycol grease to a new piston.

  1. Install the piston into the master cylinder body.



    F051194
  1. Using 2 screwdrivers, install a new C-ring while pressing the piston.

    NOTICE:
    Do not damage the rubber lips on the piston when reassembling.



3. INSTALL MASTER CYLINDER BOOT


4. INSTALL MASTER CYLINDER PUSH ROD CLEVIS


F051192E01
  1. Install the master cylinder side lock nut and rod operating adapter.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



    F051191E01
  1. Install the lock nut and push rod clevis.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }



5. INSTALL MASTER CYLINDER SOLENOID


F051196
  1. Place a new gasket onto the master cylinder solenoid.



    F051195E01
  1. Install the master cylinder solenoid with 6 new bolts.

    Torque:
    32 N*m{ 325 kgf*cm , 24 ft.*lbf }

    NOTICE:
    Do not let water, dust, or other foreign matter adhere to the surface or fitting surfaces of the master cylinder solenoid, master cylinder body and gasket.



6. INSTALL BRAKE BOOSTER PUMP BRACKET


F051189E01
  1. Using a 5 mm hexagon wrench, install the brake booster pump bracket with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Install the bush onto the brake booster pump bracket.



7. INSTALL BRAKE ACTUATOR BRACKET


F051423
  1. Using a 5 mm hexagon wrench, install the brake actuator bracket with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



8. INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY


F051415E01
  1. Using a 4 mm hexagon wrench, install the 2 pins.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Install the 2 collars and 2 bushes onto the brake booster with accumulator pump assembly.



    F051188
  1. Install the brake booster with accumulator pump assembly.



    F051199
  1. Install a new clip.



    F051520E02
  1. Install the wire harnesses with the 2 screws.

    Torque:
    2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



    F051519E02
  1. Install 2 new plugs.



9. INSTALL BRAKE ACTUATOR NO. 1 TUBE


F051184E02
  1. Using a union nut wrench, install the brake actuator tube.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.



10. INSTALL BRAKE ACTUATOR HOSE NO.1


F051182E01
  1. Using needle-nose pliers, install the brake actuator hose with the 2 clips.



11. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
  1. Apply lithium soap base glycol grease to 3 new grommets.



    F051416
  1. Install the 3 grommets onto the master cylinder body.

    NOTICE:
    The grommets are different sizes. Install the grommets in their correct positions.



    F051178E01
  1. Install the master cylinder reservoir with the screw.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



    F051177
  1. Using a pin punch and hammer, install a new pin onto the master cylinder reservoir.



12. INSTALL BRAKE ACTUATOR NO. 1 BRACKET
  1. Install the fluid level warning switch connector.



    F051421
  1. Using a 5 mm hexagon wrench, install the brake actuator bracket with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }