HYDRAULIC BRAKE BOOSTER > ON-VEHICLE INSPECTION |
| 1. INSPECT BRAKE MASTER CYLINDER FLUID PRESSURE CHANGE |
Inspect the positive battery voltage.
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.
![]() |
Install a LSPV gauge (SST) and brake pedal effort gauge, and bleed the air.
When the booster does not operate:
Depress the brake pedal and check the fluid pressure.
| Front brake pressure | Rear brake pressure |
| 3,150kPa (32.1 kgf/cm2, 457 psi) or more | 0 kPa (0 kgf/cm2, 0 psi) |
| Front brake pressure | Rear brake pressure |
| 4,540 kPa (46.3 kgf/cm2, 659 psi) or more | 0 kPa (0 kgf/cm2, 0 psi) |
When the booster operates:
Turn the ignition switch to ON, and wait until the pump motor has stopped (step A).
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (step B).
Repeat steps A and B 5 times (step C).
Turn the ignition switch to ON, and check that the pump stops after approximately 8 to 14 seconds.
Depress the brake pedal and check the fluid pressure.
| Front brake pressure | Rear brake pressure |
| 1,120 to 2,320 kPa (11.4 to 23.7 kgf/cm2, 162 to 337 psi) | 1,220 to 2,420 kPa (12.4 to 24.7kgf/cm2, 177 to 351 psi) |
| Front brake pressure | Rear brake pressure |
| 3,840 to 5,040 kPa (39.2 to 51.4 kgf/cm2, 557 to 731 psi) | 3,990 to 5,190 kPa (40.7 to 52.9 kgf/cm2, 579 to 753 psi) |
| Front brake pressure | Rear brake pressure |
| 6,460 to 7,660 kPa (65.9 to 78.1 kgf/cm2, 937 to 1,111 psi) | 6,660 to 7,860 kPa (67.9 to 80.1 kgf/cm2, 966 to 1,140 psi) |
| Front brake pressure | Rear brake pressure |
| 8,720 to 9,920 kPa (88.9 to 101.2 kgf/cm2, 1,265 to 1,439 psi) | 11,330 to 12,530 kPa (115.5 to 127.8 kgf/cm2, 1,644 to 1,818 psi) |
| 2. INSPECT BRAKE MASTER CYLINDER OPERATION |
Inspect the positive battery voltage.
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.
Check that the brake pedal becomes easy to depress.
If the pedal does not become easy to depress, check and replace the brake line and hydraulic brake booster.
Turn the ignition switch to ON and check the pump motor operation noise.
If the pump motor does not operate, check and replace the wire harness and pump motor .
Connect the Techstream.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select "ACTIVE TEST" mode on the Techstream.
Check the master cylinder solenoid operation.

| Inspection Order (Step) | SOL Selected By Active Test | SOL To Be Activated |
| D | SRCF (SA1) | SMCF |
| E | SRCF & SRCR | SREA |
| F | SFRH | SFRH |
| G | SFLH | SFLH |
| H | SFRR & SFRH | SFRR |
| I | SFLR & SFLH | SFLR |
| J | SRMF (SMCF, SA3) | SREC |
| K | SRMR (SMCR, STR) | STR |
| L | SRRH | SRRH |
| M | SRLH | SRLH |
| N | SRH & SRR | SRRR |
| O | SRLR & SRLH | SRLR |
Prepare the vehicle.
Jack up and support the vehicle.
Release the parking brake lever.
Shift the shift lever to the "N" position and check that the rear wheels rotate by hand.
Inspect front VSC solenoid (SMCF) operation (step D).
Select "SRCF (SA1)" on the Techstream.
Turn the "SRCF (SA1)" on by the Techstream, then depress the brake pedal with stable force and check that the pedal cannot be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.
Release the brake pedal.
When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front VSC solenoid (SREA) operation (step E).
Select "SRCF & SRCR" on the Techstream.
Turn the "SRCF & SRCR" on by the Techstream, then depress the brake pedal with stable force.
When the solenoids are on, check that the front wheels do not rotate by hand.
If the front wheels rotate, replace the hydraulic brake booster.
When the solenoids are off, turn the "SRCF (SA1)" on by the intelligent, then depress the brake pedal and check the front wheels by rotating them by hand.
If the front wheels stop, replace the hydraulic brake booster.
When the "SRCF (SA1)" is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRH) operation (step F).
Select "SFRH" on the Techstream.
Turn the "SFRH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLH) operation (step G).
Select "SFLH" on the Techstream.
Turn the "SFLH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRR) operation (step H).
Select "SFRR & SFRH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SFRR & SFRH" on by the Techstream.
When the solenoids are on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLR) operation (step I).
Select "SFLR & SFLH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SFLR & SFLH" on by the Techstream.
When the solenoids are on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect rear VSC solenoid (SREC) operation (step J).
Select "SRMF (SMCF, SA3)" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRMF (SMCF, SA3)" on by the Techstream.
Release the brake pedal when the solenoid is on, and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
When the solenoid is off, check the rear wheels by rotating them by hand.
If the rear wheels stop, replace the hydraulic brake booster.
Inspect rear VSC solenoid (STR) operation (step K).
Select "SRMR (SMCR, STR)" on the Techstream.
Turn the "SRMR (SMCR, STR) on by the Techstream.
When the solenoid is on, check that the rear wheels rotate by hand.
If the rear wheels do not rotate, replace the hydraulic brake booster.
When the "SRMR (SMCR, STR)" is off, depress the brake pedal again and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRH) operation (step L).
Select "SRRH" on the Techstream.
Turn the "SRRH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLH) operation (step M).
Select "SRLH" on the Techstream.
Turn the "SRLH" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRR) operation (step N).
Select "SRH & SRR" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRH & SRR" on by the Techstream.
When the solenoids are on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLR) operation (step O).
Select "SRLR & SRLH" on the Techstream.
Depress the brake pedal with stable force, then turn the "SRLR & SRLH" on by the Techstream.
When the solenoids are on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Lower the vehicle.
Disconnect the Techstream.