Home › STEERING › POWER STEERING › VANE PUMP

VANE PUMP > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP
  1. Install the vane pump assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



2. INSTALL NO. 1 OIL RESERVOIR TO PUMP HOSE
  1. Connect the No. 1 oil reservoir to pump hose with the clip.



3. INSTALL PRESSURE FEED TUBE ASSEMBLY
  1. Install a new gasket onto the pressure feed tube.

  1. Install the pressure feed tube with the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the oil pressure switch connector.

    NOTICE:
    Make sure that no oil adheres to the connector.



4. INSTALL FAN AND GENERATOR V BELT


    A225650E01
  1. Set the fan and generator V belt onto every part.
    Text in Illustration 
    *1
    Vane Pump Assembly
    *2
    Engine Water Pump Assembly
    *3
    No. 2 Idler Pulley Sub-Assembly
    *4
    Generator Assembly
    *5
    Cooler Compressor Assembly
    *6
    No. 1 Idler Pulley Sub-Assembly
    *7
    Crankshaft Pulley
    *8
    V-ribbed Belt Tensioner Assembly

  1. While turning the V-ribbed belt tensioner assembly counterclockwise, remove the pin.

    NOTICE:
    Make sure that the fan and generator V belt is properly set to each pulley.

  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



5. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH to the front fender apron sub-assembly RH with the 4 clips.



6. INSTALL V-BANK COVER
  1. Engage the 2 hooks and install the V-bank cover to the No. 1 V-bank cover bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.



7. ADD POWER STEERING FLUID


8. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).

    2. Repeat step A several times.

  1. Stop the engine.



    C133819E02
  1. Check for foaming or emulsification.
    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.

  1. Check the fluid level.



9. CHECK FOR POWER STEERING FLUID LEAKAGE


10. INSTALL FRONT WHEEL RH

Torque:
112 N*m{ 1137 kgf*cm , 82 ft.*lbf }