Home › STEERING › POWER STEERING › VANE PUMP

VANE PUMP > REASSEMBLY

for Preparation Click here


NOTICE:
When installing, coat the parts indicated by the arrows with power steering fluid .



1. INSTALL VANE PUMP HOUSING OIL SEAL


F051271E03
Text in Illustration 
*1
Oil Seal
  1. Coat a new vane pump housing oil seal lip with power steering fluid.

  1. Using SST and a press, install a new oil seal.

    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction.



2. INSTALL PULLEY SHAFT SUB-ASSEMBLY


F051272E03
Text in Illustration 
*a
Power Steering Fluid
  1. Coat the bushing inner surface of the vane pump housing front with power steering fluid.

  1. Gradually insert the vane pump shaft.

    NOTICE:
    Do not damage the vane pump housing oil seal lip in the vane pump housing front.



3. INSTALL VANE PUMP FRONT SIDE PLATE


F051267
  1. Coat a new O-ring with power steering fluid and install it onto the vane pump housing front.



    C065368
  1. Coat a new O-ring with power steering fluid and install it onto the side plate.



    F051273
  1. Align the dent of the side plate with that of the vane pump housing front and install the side plate.

    NOTICE:
    Make sure that the side plate is installed facing the correct direction.



4. INSTALL VANE PUMP CAM RING


F051274E02
Text in Illustration 
*a
Inscribed Mark
  1. Align the dent of the cam ring with that of the side plate and install the cam ring with the inscribed mark facing outward.



5. INSTALL VANE PUMP ROTOR


F051275E03
Text in Illustration 
*a
Inscribed Mark
*b
Round End
  1. Install the vane pump rotor with the inscribed mark facing outward.

  1. Coat the 10 vane plates with power steering fluid.

  1. Install the vane plates with the round ends facing outward.



    F051276
  1. Using a snap ring expander, install a new snap ring onto the pulley shaft.



6. INSTALL VANE PUMP REAR HOUSING


    C131230
  1. Coat a new O-ring with power steering fluid and install it onto the vane pump housing rear.

  1. Align the straight pin of the vane pump housing rear with the dents of the cam ring, side plate and vane pump housing front, and install the vane pump housing rear with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



7. INSPECT PRELOAD


C053369
  1. Check that the pump rotates smoothly without making any abnormal noises.

  1. Provisionally install the service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.3937 in.)
    Thread pitch:
    1.25 mm (0.0492 in.)
    Bolt length:
    50 mm (1.9685 in.)

  1. Using a torque wrench, check the pump rotating torque.

    Torque:
    0.27 N*m{ 2.8 kgf*cm , 2.4 in.*lbf }



8. INSTALL FLOW CONTROL VALVE


F051277
  1. Coat the compression spring and flow control valve with power steering fluid.

  1. Install the compression spring and flow control valve.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }



9. INSTALL PRESSURE FEED TUBE
  1. Install 2 new gaskets onto the pressure feed tube.



    C217274E01
  1. Install the pressure feed tube with the bolt.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }

    Text in Illustration 
    *a
    36.5° to 43.5°

    HINT:
    Perform the installation with the pressure feed tube at the correct angle.



10. INSTALL POWER STEERING SUCTION PORT UNION


    C217272
  1. Coat a new O-ring with power steering fluid, and install it onto the suction port union.

  1. Install the suction port union with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }