Home › TRANSMISSION ยท RA61F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer onto the transmission.

  1. Install the 2 clamps and 8 bolts.

    Torque:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }



2. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY


C233034
  1. Install the manual transmission case cover with the 5 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



3. INSTALL MANUAL TRANSMISSION WITH TRANSFER


F051064E02
  1. Install the manual transmission with transfer with the 9 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B



4. CONNECT WIRE HARNESS


5. CONNECT CONNECTOR
  1. Connect the back-up light switch connector.

  1. Connect the speedometer sensor connector.

  1. Connect the 2 transfer indicator switch connectors.



6. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


C135786
  1. Install engine mounting insulator rear No. 1 with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



7. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C135785
  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }

  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



8. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


C129541
  1. Install the front suspension member bracket LH with the 4 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



9. INSTALL FRONT SUSPENSION MEMBER BRACKET RH


C129542
  1. Install the front suspension member bracket RH with the 4 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



10. INSTALL CLUTCH ACCUMULATOR ASSEMBLY


    F050798
  1. Install the clutch accumulator with the 3 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



    C133798
  1. Using a union nut wrench, tighten the flexible hose tube.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install the clutch line bracket with the nut

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    C133797
  1. Using a union nut wrench, connect the flexible hose tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install the clutch line bracket with the bolt.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



11. INSTALL ACCUMULATOR TO FLEXIBLE HOSE TUBE


C135784
  1. Using a union nut wrench, connect the hose tube. (for flexible hose side)

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install a new clip.



    C135783
  1. Using a union nut wrench, connect the hose tube. (for accumulator side)

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Install the 3 nuts and connect the hose tube.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



12. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY


F050800
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



13. INSTALL NO. 1 CLUTCH HOUSING COVER


F050796
  1. Install the No. 1 clutch housing cover with the 3 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



14. INSTALL FLYWHEEL HOUSING SIDE COVER


F050352
  1. Install the flywheel housing side cover onto the cylinder block.



15. INSTALL STARTER ASSEMBLY
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the bolt and nut.

    Torque:
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for nut:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



16. INSTALL MANIFOLD STAY


F051649
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



17. INSTALL NO. 2 MANIFOLD STAY


F051648
  1. Install the No. 2 manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



18. INSTALL PROPELLER SHAFT ASSEMBLY


C098700E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098699E02
  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



19. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


    C098708E04
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E03
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



20. INSTALL PROPELLER SHAFT HEAT INSULATOR


C133778
  1. Install the propeller shaft heat insulator with the 2 bolts.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



21. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold RH.



    A128851
  1. Install the exhaust front pipe with 2 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



    A128852E01
  1. Install a new gasket onto the front exhaust pipe.

    1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the front exhaust pipe end.

      NOTICE:
      1. Make sure that the gasket is in the correct direction when installing.
      2. Do not reuse the removed gasket.
      3. Do not push in the gasket with the exhaust pipe when connecting it.



22. INSTALL NO. 2 FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold LH.

  1. Install a new gasket onto the No. 2 front exhaust pipe.



    A129938
  1. Install the front No. 2 exhaust pipe with 2 new nuts and 2 bolts and exhaust pipe support.

    Torque:
    Nut:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }
    Bolt:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



    A129939
  1. Install the exhaust pipe stopper bracket with the 2 bolts (for 4WD).

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



23. ADD MANUAL TRANSMISSION OIL


24. ADJUST MANUAL TRANSMISSION OIL


D025304E01
  1. Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest point of the transmission filler plug opening.

    Manual Transmission Oil:
    Oil Grade:
    API GL-4
    Viscosity:
    SAE 75W-90
    Standard Capacity:
    1.8 Liters (1.9 US qts, 1.6 Imp. qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage when the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



25. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY


F051066E02
  1. Apply MP grease to the tip of the shift lever.



    F051824E01
  1. Cover the shift lever cap with a cloth.

  1. Pressing down on the shift lever cap, turn it clockwise to install the shift lever.



26. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E03
  1. Install the transfer shift lever onto the shift lever retainer.

  1. Using needle-nose pliers, install the snap ring.



27. INSTALL SHIFT LEVER BOOT ASSEMBLY


C135788
  1. Install the shift lever boot with the 4 screws and 2 clips.



28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual transmission)


29. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer)


30. INSTALL FRONT CONSOLE BOX


    B133851
  1. Engage the 5 claws and install the front console box.

  1. Install the 4 <D> screws.



31. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B133897
  1. Engage the 3 claws and 5 clips and install the console upper rear panel.



32. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B133901E01
  1. Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.

  1. Engage the 4 claws and install the parking brake hole cover.



33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



34. INSPECT FOR EXHAUST GAS LEAK

HINT:
Perform "Inspection After Repairs" after repairing or replacing the exhaust system (See Click herepage).