Home › TRANSMISSION ยท RA61F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B133898E02
  1. Disengage the 2 A claws and 2 B claws.

  1. Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 C claws and remove the parking brake hole cover.



3. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B133897
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and 3 claws and remove the console upper rear panel.



4. REMOVE FRONT CONSOLE BOX


    B133851
  1. Remove the 4 <D> bolts.

  1. Disengage the 5 claws and remove the console box.



5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer)


6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)


7. REMOVE SHIFT LEVER BOOT ASSEMBLY


C135788
  1. Remove the 4 screws and 2 clips, then remove the shift lever boot.



8. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C113710E04
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.



9. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


F051062
  1. Separate the shift lever cap boot from the manual transmission.



    F051209E01
  1. Cover the shift lever cap with a cloth.

  1. Pressing down on the shift lever cap, turn it counterclockwise to remove the shift lever.

  1. Pull out the shift lever.



10. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the drain plug and gasket and then drain the manual transmission oil.

  1. Install a new gasket and drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. REMOVE NO. 2 FRONT EXHAUST PIPE ASSEMBLY


    A129939
  1. Remove the 2 bolts, then remove the exhaust pipe stopper bracket. (for 4WD)



    A129938
  1. Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the front No. 2 exhaust pipe.



12. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A128851
  1. Remove the 2 nuts, then remove the front exhaust pipe.

  1. Remove the front exhaust pipe gasket.



13. REMOVE PROPELLER SHAFT HEAT INSULATOR


C133778
  1. Remove the 2 bolts and remove the propeller shaft heat insulator.



14. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C098708E04
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4bolts and 4 washers.



    C098709E03
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and the propeller shaft assembly.



15. REMOVE PROPELLER SHAFT ASSEMBLY


C098699E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and 4 washers.



    C098700E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and the propeller shaft assembly.



16. REMOVE NO. 2 MANIFOLD STAY


F051648
  1. Remove the 3 bolts and remove the No. 2 manifold stay.



17. REMOVE MANIFOLD STAY


F051649
  1. Remove the 3 bolts and remove the manifold stay.



18. REMOVE STARTER ASSEMBLY


    A222905
  1. Remove the bolt and ground wire.

  1. Disconnect the starter connector.

  1. Open the terminal cap.

  1. Remove the nut and bolt, and then disconnect the starter wire.



    A218197
  1. Remove the 2 bolts and starter.



19. REMOVE FLYWHEEL HOUSING SIDE COVER


F050352
  1. Remove the flywheel housing side cover from the cylinder block.



20. REMOVE NO. 1 CLUTCH HOUSING COVER


F050796
  1. Remove the 3 bolts and No. 1 clutch housing cover.



21. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY


F050800
  1. Remove the 2 bolts and pull out the clutch release cylinder.



22. REMOVE ACCUMULATOR TO FLEXIBLE HOSE TUBE


C135783
  1. Using a union nut wrench, disconnect the hose tube. (for accumulator side)

  1. Remove the 3 nuts and disconnect the hose tube.



    C135784
  1. Using a union nut wrench, disconnect the hose tube. (for flexible hose side)

  1. Remove the clip



23. REMOVE CLUTCH ACCUMULATOR ASSEMBLY


C133797
  1. Using a union nut wrench, disconnect the flexible hose tube from the clutch accumulator.

    HINT:
    Use a container to catch the fluid.

  1. Remove the bolt and clutch line bracket.



    C133798
  1. Using a union nut wrench, disconnect the flexible hose tube from the clutch accumulator.

  1. Remove the nut and clutch line bracket.



    F050798
  1. Remove the 3 bolts and clutch accumulator.



24. SUPPORT MANUAL TRANSMISSION WITH TRANSFER
  1. Support the manual transmission with a transmission jack.



25. REMOVE FRONT SUSPENSION MEMBER BRACKET LH


C129541
  1. Remove the 4 bolts and remove the front suspension member bracket LH.



26. REMOVE FRONT SUSPENSION MEMBER BRACKET RH


C129542
  1. Remove the 4 bolts and remove the front suspension member bracket RH.



27. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C135785
  1. Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts and 4 bolts and remove the No. 3 frame crossmember sub-assembly.



28. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C135786
  1. Remove the 4 bolts and engine mounting insulator rear from the manual transmission.



29. DISCONNECT CONNECTOR
  1. Tilt down the transmission.

  1. Disconnect the 2 transfer indicator switch connectors.

  1. Disconnect the speedometer sensor connector.

  1. Disconnect the back-up light switch connector.



30. DISCONNECT WIRE HARNESS


31. REMOVE MANUAL TRANSMISSION WITH TRANSFER


F051064
  1. Remove the 9 bolts.

  1. Separate and remove the manual transmission.



32. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY


C233034
  1. Remove the 5 bolts and remove the manual transmission case cover.



33. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.