Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

DTC    01-DC    Transmission Error

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
01-DC
*1
Transmission to component shown by sub-code failed (Detecting this DTC does not always mean actual failure).
If the same sub-code is stored in other components, check power source circuit and communication system of all components shown by sub-code

HINT:
*1: If the ignition switch is turned off after idling for 60 seconds, this DTC may be stored when the engine is started again.

NOTICE:
  1. Before starting troubleshooting, be sure to clear the DTCs stored due to the reason described in the HINT above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver assembly is the master unit.
  3. Be sure to clear and recheck for the DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedure.

1.CHECK FOR DTC OF OTHER COMPONENTS
  1. Check if the component shown by the sub-code is displayed in the check result of the other components.

    1. Check if "01-DC" is output for the other components.

    2. If "01-DC" is output for any other components, check if the same physical address is displayed.

      Result 
      Result
      Proceed to
      "01-DC" is output and the same physical address is displayed
      A
      "01-DC" is not output or the same physical address is not displayed
      B

      HINT:
      For the list of the components shown by sub-codes, refer to the table in step 2.



B
Go to step 4
A


2.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE


  1. Enter diagnostic mode.


    E110915E13

  1. Press preset switch "2" to change the mode to "Detailed Information Mode".

  1. Identify the component which has stored this code.

    Component Table 
    Component
    Physical Address
    Stereo component amplifier assembly*1
    440
    Satellite radio tuner
    1F1
    Radio receiver assembly
    190
    Multi-media interface ECU
    388
    *1: w/ Stereo Component Amplifier Assembly

    HINT:
    1. "P440" set by the stereo component amplifier assembly is shown in the preceding illustration as an example.
    2. For details of the DTC display, refer to DTC Check/Clear (Click here).


NEXT


3.CHECK COMPONENT WHICH HAS STORED THIS CODE
  1. Select the component which has stored this code.

    Component Table 
    Component
    Proceed to
    Stereo component amplifier assembly*1
    Stereo component amplifier communication error (Click here)
    Satellite radio tuner
    Satellite radio tuner communication error (Click here)
    Radio receiver assembly
    Radio receiver communication error (Click here)
    Multi-media interface ECU
    Multi-media interface ECU communication error (Click here)
    *1: w/ Stereo Component Amplifier Assembly


NEXT

END 

4.CLEAR DTC
  1. Clear the DTCs (Click here).

    HINT:
    If "01-DC" is output for only one component, this may not indicate a malfunction.


NEXT


5.RECHECK FOR DTC
  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    Malfunction disappears.



NG
Go to step 6
OK

END 

6.CHECK COMPONENT WHICH HAS STORED THIS CODE
  1. Select the component which has stored this code.

    Component Table 
    Component
    Proceed to
    Stereo component amplifier assembly*1
    Stereo component amplifier communication error (Click here)
    Satellite radio tuner
    Satellite radio tuner communication error (Click here)
    Radio receiver assembly
    Radio receiver communication error (Click here)
    Multi-media interface ECU
    Multi-media interface ECU communication error (Click here)
    *1: w/ Stereo component amplifier assembly


NEXT

END