Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Taillight Relay Circuit

for Preparation Click here


DESCRIPTION

The headlight dimmer switch sends a signal to the main body ECU.

WIRING DIAGRAM


E263638E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TAIL LIGHT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the taillights while operating the taillight relay using the Techstream.

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Taillight Relay
    Taillight Relay
    OFF/ON
    -

    OK:
    The taillights come on when operating it through the Techstream.


Result:

Result
Proceed to
OK
A
No illumination lights illuminate
B
Front turn signal light does not illuminate
C
Taillight or license plate light does not illuminate
D
Outer rear view mirror illumination light does not illuminate
E



B
Go to step 2

C
Go to step 5

D
Go to step 7

E
Go to step 10
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (TAIL FUSE)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω

  1. Reinstall the TAIL fuse.



NG
REPLACE FUSE
OK


3.INSPECT TAIL RELAY
E109078E06
  1. Remove the TAIL relay from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Apply the battery voltage between terminals 1 and 2
Below 1 Ω

  1. Reinstall the TAIL relay.



NG
REPLACE TAIL RELAY
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - TAIL RELAY)
B138193E01
  1. Remove the TAIL relay from the main body ECU.

  1. Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection
Condition
Specified Condition
1 - Body ground
Always
11 to 14 V
5 - Body ground
Always
11 to 14 V

  1. Reinstall the TAIL relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT BULB (FRONT TURN SIGNAL LIGHT)
B136088E01
  1. Remove the front turn signal lights.

  1. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates

  1. Reinstall the front turn signal lights.



NG
REPLACE BULB
OK


6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT TURN SIGNAL LIGHT)
B138191E01
  1. Disconnect the A16 and A20 front turn signal light connectors.

  1. Disconnect the 1B main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
A16-1 - 1B-9
Always
Below 1 Ω
A20-1 - 1B-11
Always
Below 1 Ω
A16-1 or 1B-9 - Body ground
Always
10 kΩ or higher
A20-1 or 1B-11 - Body ground
Always
10 kΩ or higher

  1. Reconnect the front turn signal light connectors.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND) 

7.INSPECT BULB (TAILLIGHT)
B141038E01
  1. Remove the taillights.

  1. Apply battery voltage to the terminals and check that the taillight illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 1
Negative battery - Terminal 2
Taillight illuminates

  1. Reinstall the taillights.



NG
REPLACE BULB
OK


8.INSPECT BULB (LICENSE PLATE LIGHT)
B138194E01
  1. Remove the license plate light.

  1. Apply battery voltage to the terminals and check that the license plate light illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 1
Negative battery - Terminal 2
Licence plate light illuminates

  1. Reinstall the license plate light.



NG
REPLACE BULB
OK


9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - TAILLIGHT, LICENSE PLATE LIGHT)
B138195E01
  1. Disconnect the L11 and L14 taillight connectors.

  1. Disconnect the S1 license plate light connector.

  1. Disconnect the 1F main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
1F-13 - L11-2
Always
Below 1 Ω
1F-13 - L14-2
Always
Below 1 Ω
1F-13 - S1-2
Always
Below 1 Ω
1F-13 or L11-2 or Body ground
Always
10 kΩ or higher
1F-13 or L14-2 or Body ground
Always
10 kΩ or higher
1F-13 or S1-2 or Body ground
Always
10 kΩ or higher

  1. Reconnect the taillight connectors.

  1. Reconnect the license plate light connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TAILLIGHT, LICENSE PLATE LIGHT - BODY GROUND) 

10.INSPECT BULB (OUTER REAR VIEW MIRROR ILLUMINATION LIGHT)
B138196E01
  1. Remove the outer rear view mirror assembly.

  1. Apply battery voltage to the terminals and check that the outer rear view mirror illumination light illuminates.

OK:
Measurement Condition
Specified Condition
Positive battery - Terminal 2
Negative battery - Terminal 1
Outer rear view mirror illumination light illuminates

  1. Reinstall the outer rear view mirror assembly.



NG
REPLACE BULB
OK


11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - OUTER REAR VIEW MIRROR ILLUMINATION LIGHT)
B138197E01
  1. Disconnect the H2 and G2 outer rear view mirror assembly connectors.

  1. Disconnect the 1L main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
1L-5 - H2-2
Always
Below 1 Ω
1L-5 - G2-2
Always
Below 1 Ω

  1. Reconnect the outer rear view mirror assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER REAR VIEW MIRROR ILLUMINATION LIGHT - BODY GROUND)