Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > DRL Relay Circuit

for Preparation Click here


SYSTEM DESCRIPTION

The main body ECU controls the DRL relay.

WIRING DIAGRAM


E263636E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (DAYTIME RUNNING LIGHT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the headlight (Low-beam) while operating the daytime running light relay using the Techstream.

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Relay of DRL
    DRL Relay
    OFF/ON
    -

    OK:
    The headlight (low-beam) comes on when operating it through the Techstream.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (DRL FUSE)
  1. Remove the DRL fuse from the No. 2 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DRL fuse
    Always
    Below 1 Ω

  1. Reinstall the DRL fuse.



NG
REPLACE FUSE
OK


3.INSPECT DAYTIME RUNNING LIGHT RELAY
E109076E03
  1. Remove the DRL relay from the No. 4 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Apply the battery voltage between terminals 1 and 2
Below 1 Ω

  1. Reinstall the DRL relay.



NG
REPLACE DAYTIME RUNNING LIGHT RELAY
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY - DAYTIME RUNNING LIGHT RELAY)
B136082E02
  1. Remove the DRL relay from the No. 4 engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester connection
Condition
Specified Condition
DRL relay terminal 1 - Body round
Light control switch is in HEAD position
11 to 14 V
DRL relay terminal 1 - Body round
Light control switch is in OFF or TAIL position
Below 1 V

  1. Reinstall the DRL relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY - MAIN BODY ECU)
B136083E02
  1. Remove the DRL relay from the No. 4 engine room relay block.

  1. Disconnect the 1B main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
DRL relay terminal 2 - 1B-3 (H-ON)
Always
Below 1 Ω
DRL relay terminal 2 or 1B-3 (H-ON) - Body ground
Always
10 kΩ or higher

  1. Reinstall the DRL relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY - HEADLIGHT, BODY GROUND)
B136084E02
  1. Remove the DRL relay from the No. 4 engine room relay block.

  1. Disconnect the A23 and A24 headlight connectors.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection
Condition
Specified Condition
DRL relay terminal 3 - A23-3
Always
Below 1 Ω
DRL relay terminal 3 or A23-3 - Body ground
Always
10 kΩ or higher
DRL relay terminal 3 - A24-3
Always
Below 1 Ω
DRL relay terminal 3 or A24-3 - Body ground
Always
10 kΩ or higher
DRL relay terminal 5 - Body ground
Always
Below 1 Ω

  1. Reinstall the DRL relay.

  1. Reconnect the headlight connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)