Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


CAN JUNCTION CONNECTOR

C221688E11


Text in Illustration 
*a
to ECM
*b
to Yaw Rate Sensor
*c
to Combination Meter ECU
*d
to DLC3
*e
to Steering Angle Sensor
*f
to Skid Control ECU
*g
to Center Airbag Sensor Assembly
*h
to Driving Support Switch Control ECU (w/ CRAWL)

Terminal No. (Symbol)
Wiring Color
Connect to
E86-1 (CANH)
LG-R
ECM
E86-12 (CANL)
LG-B
ECM
E86-2 (CANH)
LG
Yaw Rate Sensor
E86-13 (CANL)
L
Yaw Rate Sensor
E86-3 (CANH)
R
Combination Meter ECU
E86-14 (CANL)
W
Combination Meter ECU
E86-4 CANH)
P
DLC3
E86-15 (CANL)
V
DLC3
E86-5 (CANH)
B
Steering Angle Sensor
E86-16 (CANL)
Y
Steering Angle Sensor
E86-6 (CANH)
B
Skid Control ECU
E86-17 (CANL)
W
Skid Control ECU
E86-7 (CANH)
Y
Center Airbag Assembly
E86-18 CANL)
B
Center Airbag Assembly
E86-8 (CANH)
V
Driving Support Switch Control ECU*1
E86-19 (CANL)
G
Driving Support Switch Control ECU*1
  1. *1: w/ CRAWL

DLC3
E191939E07
  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    P - V
    Ignition switch off
    54 to 69 Ω
    E1-6 (CANH) - E1-4 (CG)
    P - W-B
    Ignition switch off
    200 Ω or more
    E1-14 (CANL) - E1-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or more
    E1-6 (CANH) - E1-16 (BAT)
    P - B-R
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    V - B-R
    Ignition switch off
    6 kΩ or more


BRAKE ACTUATOR (SKID CONTROL ECU)
E191994E01
  1. Turn the ignition switch off.

  2. Disconnect the skid control ECU connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator (Skid Control ECU))

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A4-11 (CANH) - A4-32 (GND2)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A4-25 (CANL) - A4-32 (GND2)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A4-11 (CANH) - A4-31 (+BS)
    B - Y
    Ignition switch off
    6 kΩ or higher
    A4-25 (CANL) - A4-31 (+BS)
    W - Y
    Ignition switch off
    6 kΩ or higher


ECM

E191996E02


Text in Illustration 
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Turn the ignition switch off.

  2. Disconnect the ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E77-32 (CANH) - E77-31 (CANL)
    LG-R - LG-B
    Ignition switch off
    108 to 132 Ω
    E77-32 (CANH) - B50-14 (E01)
    LG-R - BR
    Ignition switch off
    200 Ω or higher
    E77-31 (CANL) - B50-14 (E01)
    LG-B - BR
    Ignition switch off
    200 Ω or higher
    E77-32 (CANH) - E78-24 (BATT)
    LG-R - L
    Ignition switch off
    6 kΩ or higher
    E77-31 (CANL) - E78-24 (BATT)
    LG-B - L
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR
E218497E02
  1. Turn the ignition switch off.

  2. Disconnect the yaw rate sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    *b
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E81-3 (CANH) - E81-2 (CANL)
    LG - L
    Ignition switch off
    54 to 69 Ω
    E81-3 (CANH) - E81-1 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E81-2 (CANL) - E81-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E81-3 (CANH) - E1-16 (BAT)
    LG - B-R
    Ignition switch off
    6 kΩ or higher
    E81-2 (CANL) - E1-16 (BAT)
    L - B-R
    Ignition switch off
    6 kΩ or higher


STEERING ANGLE SENSOR
E192049E01
  1. Turn the ignition switch off.

  2. Disconnect the steering angle sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    B - Y
    Ignition switch off
    54 to 69 Ω
    E16-3 (CANH) - E16-2 (ESS)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E16-11 (CANL) - E16-2 (ESS)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    E16-3 (CANH) - E16-9 (BAT)
    B - W-R
    Ignition switch off
    6 kΩ or higher
    E16-11 (CANL) - E16-9 (BAT)
    Y - W-R
    Ignition switch off
    6 kΩ or higher


COMBINATION METER ECU
E214876E01
  1. Turn the ignition switch off.

  2. Disconnect the combination meter ECU connectors.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination meter ECU)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E14-10 (CANH) - E14-9 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    E14-10 (CANH) - E13-21 (ES)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E14-9 (CANL) - E13-21 (ES)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E14-10 (CANH) - E13-1 (B)
    R - R
    Ignition switch off
    6 kΩ or higher
    E14-9 (CANL) - E13-1 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


AIRBAG SENSOR ASSEMBLY
E176022E05
  1. Turn the ignition switch off.

  2. Disconnect the airbag sensor assembly, connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E29-13 (CANH) - E29-22 (CANL)
    Y - B
    Ignition switch off
    54 to 69 Ω
    E29-13 (CANH) - E1-4 (CG)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    E29-22 (CANL) - E1-4 (CG)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E29-13 (CANH) - E1-16 (BAT)
    Y - B-R
    Ignition switch off
    6 kΩ or higher
    E29-22 (CANL) - E1-16 (BAT)
    B - B-R
    Ignition switch off
    6 kΩ or higher


DRIVING SUPPORT SWITCH CONTROL ECU (w/ CRAWL)


    E257628E07
  1. Turn the ignition switch off.

  2. Disconnect the driving support switch control ECU connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Driving Support Switch Control ECU)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E89-8 (CANH) - E89-3 (CANL)
    V - G
    Ignition switch off
    54 to 69 Ω
    E89-8 (CANH) - E89-16 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    E89-3 (CANL) - E89-16 (GND)
    G - W-B
    Ignition switch off
    200 Ω or higher
    E89-8 (CANH) - E89-6 (+B)
    V - W-R
    Ignition switch off
    6 kΩ or higher
    E89-3 (CANL) - E89-6 (+B)
    G - W-R
    Ignition switch off
    6 kΩ or higher