Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the CAN bus lines (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.

  2. Relationships between components and system functions and effects of communication failure on these functions. (For further details, see the pages for each system.)

    Function
    Behavior during CAN Failure
    1. Control Master
    2. System Related
    Vehicle Behavior
    DTC
    (Driver Detectable)
    Diagnostic Trouble Code
    VDM Control
    (Calculates torque level desired by driver based on accelerator pedal operation and controls torque according to this and other conditions in order to achieve smoother driving performance and improved stability, startability, reacceleration, and acceleration feel.)
    1. ECM
    2. Skid control ECU, Yaw rate sensor, Steering angle sensor
    Does not calculate desired torque based on accelerator pedal operation, and does not provide smoother driving performance or improved stability, startability, reacceleration, or acceleration feel.
    Nothing
    (Does not calculate desired torque based on accelerator pedal operation, and does not provide smoother driving performance or improved stability, startability, reacceleration, or acceleration feel.)
    Nothing
    ECT indicator in meter
    (Shift position, switch, mode, etc.)
    1. ECM
    2. Combination meter ECU
    Indicators do not turn on.
    Nothing
    (Indicators do not turn on.)
    Nothing
    AI-SHIFT control
    (Control the A/T in order to improve engine braking power and acceleration feeling.)
    1. ECM
    2. Skid control ECU
    AI-SHIFT control does not operate.
    Nothing
    (AI-SHIFT control does not operate.)
    Nothing
    Cruise control
    (Adjusts the engine throttle valve opening amount automatically to control the vehicle.)
    1. ECM
    2. Skid control ECU, Combination meter ECU
    Cruise control does not operate.
    Nothing
    (Indicator light blinks.)
    Nothing
    VSC control
    (Prevent skid when cornering.)
    1. Skid control ECU
    2. ECM, Yaw rate sensor, Steering angle sensor
    VSC does not operate.
    (Light turns on.)
    U0073
    U0100
    U0123
    U0124
    U0126
    TRC control
    (Stabilize vehicle start.)
    1. Skid control ECU
    2. ECM, Yaw rate sensor, Steering angle sensor
    TRC does operate.
    (Light turns on.)
    U0073
    U0100
    U0123
    U0124
    U0126
    ABS control
    (Prevents wheels from locking during sudden braking.)
    1. Skid control ECU
    2. Yaw rate sensor
    ABS does not operate.
    (Light turns on.)
    U0073
    U0123
    U0124
    Tachometer
    (Controls the tachometer according to engine speed signal.)
    1. Combination meter ECU
    2. ECM
    The tachometer displays 0 rpm.
    Nothing
    (Tachometer displays 0 rpm.)
    U0100
    Engine coolant temperature gauge
    (Controls the gauge according to the engine coolant temperature signal.)
    1. Combination meter ECU
    2. ECM
    The temperature gauge needle is at the middle of the "C" mark or below.
    Nothing
    (The temperature gauge needle is at the middle of the "C" mark or below.)
    Nothing
    Transmission fluid temperature gauge
    (Controls the gauge according to the transmission fluid signals.)
    1. Combination meter ECU
    2. ECM
    Control continues based on the last signal received.
    Nothing
    (Control continues based on the last signal received.)
    Nothing
    Speedometer
    (Receives vehicle speed signal and drives indicator needle.)
    1. Combination meter ECU
    2. Skid control ECU
    Input signal controlled as 0 km/h.
    Nothing
    (Input signal commanded to 0 km/h.)
    U0129
    Telltale
    (Turns on, flashes, or turns off indicators based on CAN input signal.)
    1. Combination meter ECU
    2. Skid control ECU, Airbag sensor assembly
    Control continues based on the last signal received, or the indicator turns on.
    Nothing
    (Control continues based on the last signal received, or the indicator turns on.)
    U0129
    Buzzer
    (Receives buzzer request on CAN input signal.)
    1. Combination meter ECU
    2. Skid control ECU, Airbag sensor assembly
    Does not sound.
    Nothing
    (Does not sound.)
    U0129
    U0151
    Diag code display
    (Receives diagnostic codes sent from ECU, and blinks the telltale light in the meter to match the code)
    1. Combination meter ECU
    2. ECM, Skid control ECU, Airbag sensor assembly
    Controlled as normal mode.
    Nothing
    (Cannot be detected.)
    Nothing
    Event data recorder
    (Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.)
    1. Airbag sensor assembly
    2. ECM, Combination meter ECU
    An invalid value is stored.
    Nothing
    (Cannot be detected.)
    Nothing
    Collision detection signal
    (Notifies the system of a collision in order to perform a fuel cut at the time when a vehicle collision occurs.)
    1. ECM
    2. Airbag sensor assembly
    In the event of a collision, fuel cut is not performed.
    Nothing
    (Cannot be detected.)
    Nothing
    Steering sensor
    (Detects the steering wheel angle.)
    1. Steering angle sensor
    2. Skid control ECU
    Nothing
    VSC Indicator light turns on.
    Nothing