Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY

E125398E01

  1. Disconnect the E13 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-1 (B) - Body ground
    R - Body ground
    Battery
    Always
    11 to 14 V
    E13-2 (IG+) - Body ground
    R-L - Body ground
    Ignition switch signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    E13-21 (ES) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Disconnect the E14 combination meter assembly connector.



  4. Measure the voltage and resistance of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-5 (E3) - Body ground
    Y-B - Body ground
    Fuel level signal
    Ignition switch ON
    11 to 14 V
    E13-7 (WRNP) - Body ground
    LG - Body ground
    Passenger side seat belt warning light signal (Output)
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is unfastened
    11 to 14 V → Below 1 V
    Ignition switch ON
    Front passenger seat is occupied and its seat belt is fastened
    Below 1 V
    E13-8 (L) - Body ground
    G-Y - Body ground
    Seat belt condition signal (Driver side)
    D-BELT indicator light ON → OFF
    Below 1 V → 11 to 14 V
    E13-9 (KSW) - Body ground
    V-G - Body ground
    Key switch condition signal
    Key inserted → removed
    Below 1 V → 11 to 14 V
    E13-11 (ILL-) - Body ground
    BR-W - Body ground
    Light control rheostat signal
    Ignition switch off → ON
    Pulse generation
    (See waveform 1)
    E13-13 (SI) - Body ground
    GR-R - Body ground
    Vehicle speed signal (Input)
    Driving at approx. 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    E13-14 (+S) - Body ground
    V-R - Body ground
    Vehicle speed signal (Input)
    Ignition switch ON and wheel turning slowly
    Pulse generation
    (See waveform 2)
    E13-16 (L) - Body ground
    V-W - Body ground
    Fuel level signal
    Ignition switch ON
    11 to 14 V
    E13-18 (B) - Body ground
    P - Body ground
    Turn signal RH signal
    Ignition switch ON
    Turn signal RH indicator light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    E13-19 (R/O) - Body ground
    L-Y - Body ground
    RSCA OFF indicator light input signal
    Ignition switch ON
    RSCA OFF indicator light ON → OFF
    Below 1 V → 11 to 14 V
    E13-20 (B) - Body ground
    L-W - Body ground
    Turn signal LH signal
    Ignition switch ON
    Turn signal LH indicator light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    E13-23 (SW) - Body ground
    V-Y - Body ground
    All door condition signal
    All doors open → closed
    Below 1 V → 11 to 14 V
    E13-24 (WLVL)*1 - Body ground
    BR-Y - Body ground
    Washer signal
    Washer level warning light ON → OFF
    Below 1 V → 11 to 14 V
    E13-26 (+) - Body ground
    R-W - Body ground
    HEAD light signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    E13-29 (DOOR) - Body ground
    W-L - Body ground
    Driver side door open
    Driver side door open → closed
    Below 1 V → 11 to 14 V
    E13-32 (TIRE) - Body ground
    P-B - Body ground
    Tire pressure warning light signal
    Ignition switch ON
    Tire pressure warning light ON
    0.9 to 3.2 V
    Ignition switch ON
    Tire pressure warning light OFF
    3.2 V or higher
    E14-1 (RRSW)*2 - Body ground
    L-Y - Body ground
    Rear differential lock signal
    Rear differential lock warning light ON → OFF
    Below 1 V → 11 to 14 V
    E14-2 (SW)*3 - Body ground
    GR - Body ground
    4WD signal
    Center differential lock indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-2 (SW)*4 - Body ground
    R-L - Body ground
    4WD signal
    4WD indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-3 (CHG-) - Body ground
    GR - Body ground
    Charge signal
    Ignition switch ON → off
    11 to 14 V → Below 1 V
    E14-7 (CHK) - Body ground
    R-B - Body ground
    Check engine warning light signal
    Check engine warning light signal ON → OFF
    Below 1 V → 11 to 14 V
    E14-9 (CANL) - Body ground
    W - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    E14-10 (CANH) - Body ground
    R - Body ground
    CAN communication signal
    Ignition switch off
    200 Ω or higher
    E14-12 (S) - Body ground
    LG-B - Body ground
    Oil pressure signal
    Oil pressure warning light ON → OFF
    Below 1 V → 11 to 14 V
    E14-13 (ILL+) - Body ground
    G - Body ground
    Taillight signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    E14-14 (L)*5 - Body ground
    B-L - Body ground
    A/T shift position signal (L)
    A/T L indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-15 (2)*5 - Body ground
    P-L - Body ground
    A/T shift position signal (2)
    A/T 2 indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-16 (3)*5 - Body ground
    W-R - Body ground
    A/T shift position signal (3)
    A/T 3 indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-17 (4)*5 - Body ground
    L - Body ground
    A/T shift position signal (4)
    A/T 4 indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-18 (D)*5 - Body ground
    R-G - Body ground
    A/T shift position signal (D)
    A/T D indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-19 (N)*5 - Body ground
    G-W - Body ground
    A/T shift position signal (N)
    A/T N indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-20 (R)*3 - Body ground
    R-Y - Body ground
    M/T shift position signal (R)
    M/T shift reverse buzzer OFF → ON
    Below 1 V → 11 to 14 V
    E14-20 (R)*5 - Body ground
    R-Y - Body ground
    A/T shift position signal (R)
    A/T R indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-21 (P)*5 - Body ground
    Y-B - Body ground
    A/T shift position signal (P)
    A/T P indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-22 (A/T3)*4 - Body ground
    B-R - Body ground
    Transfer indicator switch neutral position signal
    AT P indicator OFF → ON
    Below 1 V → 11 to 14 V
    E14-24 (RHCL)*6 - Body ground
    W-G - Body ground
    Ground (Illumination ground)
    Always
    Below 1 V

    1. *1: for Canada
    2. *2: w/ Rear Differential Lock
    3. *3: for Manual Transmission
    4. *4: for Automatic Transmission with 4WD
    5. *5: for Automatic Transmission
    6. *6: w/ CRAWL

    HINT:
    If the result is not as specified, the combination meter assembly may be malfunctioning.




      A005138E12
    1. Waveform 1: Using an oscilloscope
      Terminal Connections
      E13-11 (ILL-) - Body Ground
      Tool Setting
      5 V/DIV., 50 ms/DIV.
      Condition
      Ignition switch ON



    2. E115032E02
    3. Waveform 2: Using an oscilloscope
      Terminal Connections
      E13-13 (SI) - Body Ground
      E13-14 (+S) - Body Ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Driving at approximately 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the cycle of the signal waveform narrows.


ACCESSORY METER ASSEMBLY

E125402E01

  1. Disconnect the F1 accessory meter assembly connector.



  2. Measure the voltage and resistance of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-1 (+B) - Body ground
    R - Body ground
    Battery
    Always
    11 to 14 V
    F1-2 (ACC) - Body ground
    GR - Body ground
    ACC
    Ignition switch off → ACC
    Below 1 V → 11 to 14 V
    F1-3 (IG+) - Body ground
    Y-R - Body ground
    Ignition switch signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    F1-4 (DMIN) - Body ground
    R-L - Body ground
    Air conditioning amplifier signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    F1-6 (ILL+) - Body ground
    G - Body ground
    Taillight signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    F1-7 (ILL-) - Body ground
    BR-W - Body ground
    Light control rheostat signal
    Ignition switch off → ON
    Pulse generation
    (See waveform 1)
    F1-8 (SI) - Body ground
    V-R - Body ground
    Combination meter signal
    Driving at approx. 5 km/h (3.1 mph)
    1 V → 9 V → 1 V
    Pulse generation
    (See waveform 2)
    F1-9 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    HINT:
    If the result is not as specified, the accessory meter assembly may be malfunctioning.




      A005138E12
    1. Waveform 1: Using an oscilloscope
      Terminal Connections
      F1-7 (ILL-) -Body Ground
      Tool Setting
      5 V/DIV., 50 ms/DIV.
      Condition
      Ignition switch ON



    2. E115032E02
    3. Waveform 2: Using an oscilloscope
      Terminal Connections
      F1-8 (SI) - Body Ground
      Tool Setting
      5 V/DIV., 20 msec/DIV.
      Condition
      Driving at approximately 5 km/h (3.1 mph)


MAIN BODY ECU

B136051E14

  1. Disconnect the E7, E8 and 1A main body ECU connectors.

  2. Measure the voltage of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E7-7 (BCTY) - Body ground
    W - Body ground
    Back door courtesy switch and back window courtesy switch input
    Back door CLOSED → OPEN
    11 to 14 V → Below 1 V
    E7-11 (RLCY) - Body ground
    P-B - Body ground
    Rear door courtesy switch signal (LH)
    Rear door (Driver side) CLOSED → OPEN
    11 to 14 V → Below 1 V
    E7-12 (RRCY) - Body ground
    P-L - Body ground
    Rear door courtesy switch signal (RH)
    Rear door (Front passenger side) CLOSED → OPEN
    11 to 14 V → Below 1 V
    E7-23 (DCTY) - Body ground
    R-B - Body ground
    Front door courtesy switch signal (Driver side)
    Driver door CLOSED → OPEN
    11 to 14 V → Below 1 V
    E7-24 (PCTY) - Body ground
    R-B - Body ground
    Front door courtesy switch signal (Passenger side)
    Front passenger door CLOSED → OPEN
    11 to 14 V → Below 1 V
    E8-14 (KSW) - Body ground
    G-Y - Body ground
    Key unlock switch condition signal
    Key inserted → removed
    Below 1 V → 11 to 14 V
    1A-7 (GND2) - Body ground)
    W - Body ground
    Ground
    Always
    Below 1 V

    HINT:
    If the result is not as specified, there may be a malfunction in the wire harness.


COMBINATION METER INTERNAL CIRCUIT

E263830E01


E258799E01


E258800E01


Connectors 
Terminal No.
Wire Harness Side
E13
1
Battery
2
Ignition switch
5
Fuel sender gauge assembly
7
Air conditioning amplifier
8
Front seat inner belt assembly (Driver side)
9
Main body ECU
11
Light control rheostat
13
Skid control ECU
14
4P-OUT (Other parts)
16
Fuel sender gauge assembly
18
Turn signal flasher assembly
19
Center airbag sensor assembly
20
Turn signal flasher assembly
21
Body ground
23
Main body ECU
24
Washer level warning switch*1
26
Main body ECU
29
Main body ECU
32
Tire pressure warning ECU
E14
1
Differential lock switch*2
2
Transfer indicator switch (center differential)*3
4WD control ECU*4
3
Generator
7
ECM
9
CAN communication line (CANL)
10
CAN communication line (CANH)
12
Engine oil pressure switch
13
TAIL relay
14
Shift lock control ECU*5
15
Shift lock control ECU*5
16
Park/neutral position switch*5
17
Shift lock control ECU*5
18
Shift lock control ECU*5
19
Park/neutral position switch*5
20
Back-up light switch*3
Park/neutral position switch*5
21
Park/neutral position switch*5
22
Transfer indicator switch (neutral position)*4
24
Each illumination part*6
  1. *1: for Canada
  2. *2: w/ Rear Differential Lock
  3. *3: for Manual Transmission
  4. *4: for Automatic Transmission with 4WD
  5. *5: for Automatic Transmission
  6. *6: w/ CRAWL