Home › BODY ELECTRICAL › WIPER AND WASHER › FRONT WIPER MOTOR

FRONT WIPER MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL FRONT WIPER MOTOR


    E127869
  1. Install the front wiper motor.

  1. Using "Torx" socket wrench T30, tighten the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    E127871
  1. Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.

  1. Install the rod onto the crank arm pivot of the front wiper motor.



    E127872
  1. Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.

  1. Install the rod onto the crank arm pivot of the front wiper motor.



2. INSTALL FRONT WIPER MOTOR AND LINK


    E127873E01
  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Connect the connector.

  1. Tighten bolt A.

  1. Tighten bolt B.

  1. Tighten 3 bolts C.

    Torque:
    7.0 N*m{ 71 kgf*cm , 61 in.*lbf }



3. INSTALL COWL TOP VENTILATOR LOUVER LH


    E127865
  1. Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.



4. INSTALL COWL TOP VENTILATOR LOUVER RH


    E127864
  1. Install the cowl top ventilator louver RH with the 3 clips and the claw.

  1. Install the hood to cowl top seal with the clip.



5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127863
  1. Install the cowl top ventilator louver sub-assembly with the 7 clips.



6. INSTALL FRONT FENDER SIDE PANEL UPPER LH
  1. Install the 4 new clips on the front fender side panel upper LH.



    B210065
  1. Engage the 4 clips and install the front fender side panel upper LH.



7. INSTALL FRONT FENDER SIDE PANEL UPPER RH
  1. Install the 4 new clips on the front fender side panel upper RH.



    B210064
  1. Engage the 4 clips and install the front fender side panel upper RH.



8. INSTALL ANTENNA ORNAMENT


    E127861E02
  1. Press in the antenna ornament in the direction shown in the illustration.



9. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY


    E148353E01
  1. Install the radio antenna pole sub-assembly by hand until fully seated.
    Text in Illustration 
    *a
    1/8 turn (20 to 45 degrees)

  1. Using a 8 mm (5/16 inch) wrench, fully tighten the radio antenna pole about 1/8 turn (20 to 45 degrees) by turning it clockwise.

    NOTICE:
    1. Do not over tighten. Tighten with finger, not hand.
    2. Do not use pliers to tighten the radio antenna pole as it can leave marks on the radio antenna pole surface.
    3. The antenna pole cannot be hand tightened to the proper specification.

    Torque:
    3.3 N*m{ 34 kgf*cm , 29 in.*lbf }



10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127876E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127875E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E127874E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



13. INSTALL WINDSHIELD WIPER ARM COVER


    E127877E01
  1. Engage the claw and install the 3 front wiper arm cover.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }