Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C215260E08


Text in Illustration 
*a
Component without harness connected
(Skid Control ECU)
-
-

Terminal No. (Symbol)
Terminal Description
A4-1 (GND1)
Skid control ECU ground
A4-2 (+BM1)
Power supply for motor
A4-3 (FR+)
Front right wheel speed sensor power supply output
A4-4 (FL-)
Front left wheel speed sensor input
A4-5 (RR+)
Rear right wheel speed sensor power supply output
A4-6 (RL-)
Rear left wheel speed sensor input
A4-7 (STP)
Stop light switch
A4-9 (CSW)
VSC OFF switch
A4-11 (CANH)
CAN communication terminal H
A4-12 (SP1)
Speedometer signal
A4-13 (ATRC)
A-TRAC switch*6
A4-14 (P)
Neutral start switch*2
A4-16 (STPO)
Stop light operation relay
A4-17 (FR-)
Front right wheel speed sensor input
A4-18 (FL+)
Front left wheel speed sensor power supply output
A4-19 (RR-)
Rear right wheel speed sensor input
A4-20 (RL+)
Rear left wheel speed sensor power supply output
A4-24 (TS)
Sensor test terminal (Signal check switch)
A4-25 (CANL)
CAN communication terminal L
A4-27 (EXI)
L4 detection switch*1*2
LL detection switch*3
A4-28 (PKB)
Parking brake switch
A4-29 (EXI4)
A.D.D. detection switch*1*2
Center differential lock detection switch*3
A4-31 (+BS)
Power supply for solenoid
A4-32 (GND2)
Skid control ECU ground
A4-40 (EXI3)
Rear differential lock detection switch*4
IG power supply*5
A4-41 (LBL)
Brake fluid level warning switch
A4-43 (NEO)
Ground (Indicates 2WD or 4WD vehicle)*1
A4-45 (STP2)
Stop light switch
A4-46 (IG1)
IG1 power supply
A5-1 (IG2)
IG2 power supply
A5-2 (+BM2)
Power supply for motor (from battery)
A5-4 (GND3)
Ground
  1. *1: for 4WD
  2. *2: for Automatic Transmission
  3. *3: for Manual Transmission
  4. *4: w/ Rear Differential Lock
  5. *5: w/o Rear Differential Lock
  6. *6: w/ A-TRAC

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.


C124764E11


Text in Illustration 
*a
Front view of wire harness connector
(Skid Control ECU)
-
-

Standard 
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A4-1 (GND1) - Body ground
W-B
Ground
Always
Below 1 Ω
A4-2 (+BM1) - Body ground
L-Y
Power supply for motor (from battery)
Always
11 to 14 V
A4-7 (STP) - Body ground
G-B
Stop light switch
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A4-9 (CSW) - Body ground
R-L
VSC OFF switch
VSC OFF switch off → on and held
10 kΩ or higher → Below 1 Ω
A4-13 (ATRC) - Body ground*6
P-G
A-TRAC switch input
A-TRAC switch off → on and held
10 kΩ or higher → Below 1 Ω
A4-14 (P) - Body ground*2
Y-B
Neutral start switch
Ignition switch ON
shift P position → any shift position except P
8 to 14 V → Below 1.5 V
A4-16 (STPO) - Body ground
B-L
Stop light operation relay
Ignition switch off → ON
Below 1 V → 11 to 14 V
A4-27 (EXI) - Body ground*1*2
W-L
L4 detection switch
Ignition switch ON
Transfer condition L4
Below 1 V
Ignition switch ON
Transfer condition except L4
11 to 14 V
A4-27 (EXI) - Body ground*3
W-L
LL detection switch
Ignition switch ON
Transfer condition LL
Below 1 V
Ignition switch ON
Transfer condition except LL
11 to 14 V
A4-28 (PKB) - Body ground
W-R
Parking brake switch
Parking brake switch off → on
10 kΩ or higher → Below 1 Ω
A4-29 (EXI4) - Body ground *1*2
GR
ADD detection switch
Ignition switch ON
Transfer condition H4 or L4
Below 1.5 V
Ignition switch ON
Transfer condition H2
11 to 14 V
A4-29 (EXI4) - Body ground*3
GR
Center differential lock detection switch
Ignition switch ON
Transfer condition LL or HL
Below 1.5 V
Ignition switch ON
Transfer condition H
11 to 14 V
A4-31 (+BS) - Body ground
Y
Power supply for solenoid (from battery)
Always
11 to 14 V
A4-32 (GND2) - Body ground
W-B
Ground
Always
Below 1 Ω
A4-40 (EXI3) - Body ground*4
L-Y
Rear differential lock detection switch
Ignition switch ON
differential lock switch ON
Below 1.5 V
Ignition switch ON
differential lock switch OFF
11 to 14 V
A4-40 (EXI3) - Body ground*5
L-Y
IG power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A4-41 (LBL) - Body ground
V-R
Brake fluid level warning switch
Brake fluid level +/-5 mm (+/-0.197 in.) from minimum level → maximum level
Below 1 Ω → 1.9 to 2.1 kΩ
A4-43 (NEO) - Body ground*1
P-L
Ground
Always
Below 1 Ω
A4-45 (STP2) - Body ground
G-Y
Stop light switch
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A4-46 (IG1) - Body ground
B-R
IG1 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A5-1 (IG2) - Body ground
B-O
IG2 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A5-2 (+BM2) - Body ground
L-Y
Power supply for motor (from battery)
Always
11 to 14 V
A5-4 (GND3) - Body ground
W-B
Ground
Always
Below 1 Ω
  1. *1: for 4WD
  2. *2: for Automatic Transmission
  3. *3: for Manual Transmission
  4. *4: w/ Rear Differential Lock
  5. *5: w/o Rear Differential Lock
  6. *6: w/ A-TRAC