Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
According to the Data List displayed on a Techstream, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in P and N
    2. ON: Shift lever in P or N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Stop Light Switch
    Stop Light Switch Status/
    OFF or ON
    1. OFF: Brake Pedal is released
    2. ON: Brake Pedal is depressed
    -
    SPD (NT)
    Input Turbine Speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Input turbine speed (NT) equal to the engine speed: Lock-Up ON (After warming up the engine)
    2. Input turbine speed (NT) nearly equal to the engine speed: Lock-Up OFF (Idling in N position)
    Data is displayed in increments of 50 rpm
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    0 km/h (0 mph): Vehicle stopped
    -
    Overdrive Cut Switch #1
    Overdrive cut signal for cruise control
    OFF or ON
    1. OFF: No shift down request
    2. ON: Shift down request
    Cruise control operating
    Shift SW Status (P Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in P
    2. ON: Shift lever in P
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (R Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in R
    2. ON: Shift lever in R
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (2 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 2 and L
    2. ON: Shift lever in 2 or L
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (L Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in L
    2. ON: Shift lever in L
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (N Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in N
    2. ON: Shift lever in N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (N,P Range) Supported
    Shift lever position P or N support status/
    Supp or Unsupp
    1. Supp: Normal
    2. Unsupp: Abnormalities in the PNP switch signal
    -
    Shift SW Status (N,P Range)
    PNP switch status/
    OFF or ON
    1. OFF: Shift lever not in P or N
    2. ON: Shift lever in P or N
    -
    Shift SW Status (D Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D
    2. ON: Shift lever in D
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (4 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in D and 4
    2. ON: Shift lever in D or 4
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    Shift SW Status (3 Range)
    PNP Switch Status/
    OFF or ON
    1. OFF: Shift lever not in 3
    2. ON: Shift lever in 3
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    HINT:
    When the failure still occurs even after adjusting these parts, Click here.
    A/T Oil Temperature 1
    No. 1 ATF Temperature Sensor Value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F): After Stall Test
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.
    A/T Oil Temperature 2
    No. 2 ATF Temperature Sensor Value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F): After Stall Test
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short.
    Lock Up
    Lock-up status/
    OFF or ON
    1. OFF: Lock-up off
    2. ON: Lock-up on
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    Actual gear position
    -
    SLT Solenoid Status
    Shift Solenoid SLT Status/
    OFF or ON
    1. OFF: Accelerator pedal is depressed
    2. ON: Accelerator pedal is released
    -
    SLU Solenoid Status
    Shift Solenoid SLU Status/
    OFF or ON
    1. OFF: Lock-up off
    2. ON: Lock-up on
    -


ACTIVE TEST

HINT:
Performing the Active Test using a Techstream allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate the shift solenoid SLU
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    OFF or ON

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate the shift solenoid S1
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N
    Activate the Solenoid (S2)
    Operate the shift solenoid S2
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    OFF or ON
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (36 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less
    Activate the Solenoid (SR)
    Operate the shift solenoid SR
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N
    Activate the Solenoid (SL1)
    Operate the shift solenoid SL1
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N
    Activate the Solenoid (SL2)
    Operate the shift solenoid SL2
    OFF or ON
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N

*: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

HINT:
The pressure values in Active Test and Hydraulic Test are different from each other.