Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Combination Meter / Data List.

  5. According to the display on the Techstream, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tail Relay SW
    Taillight relay/
    ON or OFF
    ON: Headlight dimmer switch (Light control switch) → TAIL
    OFF: Headlight dimmer switch (Light control switch) → OFF
    -
    ODO/TRIP Change SW
    ODO/TRIP switch/
    ON or OFF
    ON: ODO/TRIP switch pushed
    OFF: ODO/TRIP switch not pushed
    -
    P-Seatbelt Buckle SW
    Buckle switch (Front passenger side)/
    ON or OFF
    ON: Front passenger side seat belt is fastened
    OFF: Front passenger side seat belt is unfastened
    -
    Vehicle Speed Meter
    Vehicle speed/
    Min.: 0 (0), Max.: 255 (158)
    Approximately same as actual vehicle speed (When vehicle is being driven)
    Unit: km/h (mph)
    Engine Rpm
    Engine speed/
    Min.: 0, Max.: 12750
    Approximately same as actual engine speed (when engine is running)
    Unit: rpm
    Coolant Temperature
    Engine coolant temperature/
    Min.: 0 (32), Max.: 127.5 (261.5)
    After warming up:
    75 to 105 (167 to 221)
    Unit: °C (°F)
    Reverse Range Switch (6MT)*1
    Reverse range switch/
    ON or OFF
    ON: Reverse range switch ON
    OFF: Reverse range switch OFF
    -
    +B Voltage Value
    Battery voltage/
    Min.: 0, Max.: 25.5
    Between 1 V and 14 V
    Unit: V
    Integrated value for Maintenance*2
    Oil maintenance information integrated value/
    Min.: 0, Max.: 25500 (miles)
    Driving distance after performing oil maintenance resetting procedure displayed
    If the value is 5000 (miles) or more, perform the oil maintenance resetting procedure after changing the oil.
    Fuel Input
    Fuel input signal/
    Min.: 0, Max.: 127.5
    Fuel sender input value
    Unit: Liters
    Rheostat value
    Light control rheostat switch input/
    Min.: 0, Max.: 100
    Light control rheostat switch Dark (0 %) → Bright (100 %)
    Unit: %
    TPMS Operation State
    Condition of tire pressure warning system/
    OFF, ON or Unknown
    OFF: Tire pressure warning system not operating
    ON: Tire pressure warning system operating
    Unknown: Wire harness between combination meter assembly and tire pressure warning ECU open
    -
    Driver Side Seatbelt Warning Buzzer
    Driver side seat belt warning buzzer/
    ON or OFF
    ON: Driver side seat belt warning buzzer ON
    OFF: Driver side seat belt warning buzzer OFF
    -
    P-Seatbelt Warning Buzzer
    Front passenger side seat belt warning buzzer/
    ON or OFF
    ON: Front passenger side seat belt warning buzzer ON
    OFF: Front passenger side seat belt warning buzzer OFF
    -
    Number of Trouble Code
    Number of trouble codes/
    MIN.: 0, MAX.: 255
    Number of DTCs will be displayed
    -

    1. *1: for Manual Transmission
    2. *2: for U.S.A.


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    OFF/0/40/80/120/160*1/200*1 km/h (mph)
    Perform the test with the vehicle stopped and the engine idling.
    Acceptable range (km/h or mph): [Control range → Speedometer display]
    for mph
    1. 40 → 39.1 to 41.9
    2. 80 → 79.3 to 82.5
    for km/h
    1. 40 → 38.3 to 42.8
    2. 80 → 78.4 to 83.4
    3. 120 → 118.9 to 123.9
    4. 160 → 159.3 to 164.3
    TachoMeter Operation
    Tachometer
    OFF/0/1000/2000/3000/4000/5000/6000/7000 rpm
    Perform the test with the vehicle stopped and the engine idling.
    Fuel Meter Operation
    Fuel receiver gauge
    OFF/Empty/ 1/2 /Full
    Perform the test with the vehicle stopped and the engine idling.
    Volt Meter Operation
    Voltmeter
    OFF, 0, 3, 6, 9, 12, 15 or 18 V
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp Airbag
    Airbag warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Driver Side Seat Belt
    Driver side seat belt warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp ABS
    ABS warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp Slip
    Slip indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp Fuel
    Fuel warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    ACTIVE TRC Indicator*2
    ACTIVE TRAC indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    VSC TRC Indicator
    VSC TRAC indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Tire Pressure Warning System
    Tire Pressure warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    A/T Oil Temperature Operation*3
    A/T oil temperature warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp Cruise*4
    CRUISE indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Lamp Brake
    Brake warning light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. CRAWL*5
    CRAWL indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Maintenance Indicator*6
    Maintenance required reminder light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. Auto LSD*7
    Auto LSD indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Indicat. VSC OFF
    VSC OFF indicator light
    OFF/ON
    Perform the test with the vehicle stopped and the engine idling.
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    OFF, LOW, NORMAL or HIGH
    Perform the test with the vehicle stopped and the engine idling.
    Meter Display 1
    Meter display
    OFF/6/5/4/3/2/1/0/All
    Perform the test with the vehicle stopped and the engine idling.
    Meter Display 2
    Meter display
    OFF/9/8/7
    Perform the test with the vehicle stopped and the engine idling.

    1. *1: except U.S.A.
    2. *2: w/ Active Traction Control
    3. *3: for Automatic Transmission
    4. *4: w/ Cruise Control System
    5. *5: w/ CRAWL
    6. *6: for U.S.A.
    7. *7: for 2WD