Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.
The ECM applies a voltage to the temperature sensor through ECM terminal THO1.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance and the voltage decrease as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.

DTC No.
DTC Detection Conditions
Trouble Areas
P0711
Either of the following Condition (A) or (B) is met:
  1. Transmission wire (No. 1 ATF temperature sensor)
  2. ECM
Condition (A):
(a), (b) and (c) are detected: (2-trip detection logic)
  1. (a) After the engine is stopped, 5 hours or more elapse before the engine is started.
  2. (b) Intake air and engine coolant temperatures are 15°C (59°F) or higher after the engine is started
  3. (c) ATF temperature is below 20°C (68°F) after normal driving for 16 minutes and 40 seconds and 7.5 km (4.6 miles) or more.
Condition (B):
Both (a) and (b) are detected (2-trip detection logic).
  1. (a) Engine coolant temperature is less than 35°C (95°F) at engine start.
  2. (b) ATF temperature is 95°C (203°F) or more.

MONITOR DESCRIPTION

This DTC indicates that there is a problem with the output from the ATF (Automatic Transmission Fluid) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects any open or short malfunctions in the ATF temperature circuit or a fault of the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.
When the ATF temperature is 95°C (203°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL, and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0711: ATF temperature sensor/Rationality check
Required sensors/Components
ATF temperature sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0712, P0713, P2742, P2743 (ATF temperature sensor "A" circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0111, P011B, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)

Condition (A) 
Soak time
5 hours or more
Duration time from engine start
12 seconds or more
Time after engine start
16 minutes and 40 seconds or more
Driving distance after engine start
7.5 km/h(4.6 miles) or more
IAT (12 seconds after engine start)
15°C (59°F) or more
ECT (12 seconds after engine start)
15°C (59°F) or more

Condition (B) 
Time after ECT reaches 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
95°C (203°F) or more
ECT (12 seconds after engine start)
Below 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS

Either of the following conditions is met: Condition (A) or (B).

Condition (A) 
ATF temperature
Less than 20°C (68°F)

Condition (B) 
ATF temperature
95°C (203°F) or more

COMPONENT OPERATING RANGE


ATF temperature
20 to 95°C (68 to 203°F)

WIRING DIAGRAM


C186139E05


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
According to the Data List displayed on a Techstream, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF Temperature Sensor Value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. Approximately 80°C (176°F):
      After Stall Test
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.

    HINT:
    When DTC P0712 is output and Techstream reading is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and Techstream reading is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal THO1 and the body ground.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0711 is output
    A
    P0711 and other DTCs
    B

    HINT:
    If any codes besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID
OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) (Click here)