Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER


  1. Disconnect the E72 amplifier connector and measure the resistance according to the value(s) in the table below.


    B065593E37


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E72-7 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E72 amplifier connector and measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E72-1 (VC5) - E72-7 (AGND)
    GR-R - L
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    E72-4 (CODE) - E72-7 (AGND)
    P-G - L
    Demodulated signal of key code data
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    E72-5 (TXCT) - E72-7 (AGND)
    LG-R - L
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    If the result is not as specified, the amplifier may have a malfunction.



  3. Inspect using an oscilloscope.



      B139208E01
    1. Waveform 1
      Tester Connection
      E72-4 (CODE) - E72-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder



    2. B139205E01
    3. Waveform 2
      Tester Connection
      E72-5 (TXCT) - E72-7 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder


CHECK TRANSPONDER KEY ECU


  1. Disconnect the E79 ECU connector and measure the resistance and voltage according to the value(s) in the table below.


    B088367E23


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E79-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E79-1 (+B) - E79-16 (GND)
    W-R - W-B
    Battery
    Always
    11 to 14 V
    E79-2 (IG) - E79-16 (GND)
    B-O - W-B
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    E79-3 (KSW) - E79-16 (GND)
    G-Y - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    10 kΩ or higher
    Key is in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the E79 ECU connector and measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E79-5 (AGND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    E79-3 (KSW) - E79-16 (GND)
    G-Y - W-B
    Unlock warning switch signal
    No key is in ignition key cylinder
    11 to 14 V
    Key is in ignition key cylinder
    Below 1 V
    E79-14 (VC5) - E79-5 (AGND)
    GR-R - L
    Power source
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V
    E79-4 (TXCT) - E79-5 (AGND)
    LG-R - L
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 1
    E79-15 (CODE) - E79-5 (AGND)
    P-G - L
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    Waveform 2
    E79-13 (EFIO) - E79-16 (GND)
    L-Y - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Waveform 3
    E79-12 (EFII) - E79-16 (GND)
    L-O - W-B
    ECM input signal
    Ignition switch off
    11 to 14 V
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Waveform 4
    E79-9 (D) - E79-16 (GND)
    R-Y - W-B
    Diagnostic tester communication
    Without communication
    Below 1 V
    During communication
    Pulse generation
    E79-7 (CTY) - E79-16 (GND)
    R-B - W-B
    Door courtesy signal
    Switch pushed
    11 to 14 V
    Switch free
    Below 1 V
    E79-8 (IND) - E79-16 (GND)
    V-W - W-B
    Security indicator signal
    Security indicator light is on
    11 to 14 V
    Security indicator light is off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.



  3. Inspect using an oscilloscope.



      B139205E01
    1. Waveform 1
      Tester Connection
      E79-4 (TXCT) - E79-5 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder



    2. B139208E01
    3. Waveform 2
      Tester Connection
      E79-15 (CODE) - E79-5 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder



    4. B229709E01
    5. Waveform 3
      Tester Connection
      E79-13 (EFIO) - E79-16 (GND)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Ignition switch ON



    6. B229710E01
    7. Waveform 4
      Tester Connection
      E79-12 (EFII) - E79-16 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.


CHECK ECM


  1. Disconnect the B49 ECM connector and measure the resistance according to the value(s) in the table below.


    A193170E05


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B49-12 (E1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the B49 ECM connector. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E77-14 (IMI) - B49-12 (E1)
    L-Y - BR
    Transponder key ECU input signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Waveform 1
    E77-20 (IMO) - B49-12 (E1)
    L-O - BR
    Transponder key ECU output signal
    Ignition switch off
    11 to 14 V
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.



  3. Inspect using an oscilloscope.



      B229709E01
    1. Waveform 1
      Tester Connection
      E77-14 (IMI) - B49-12 (E1)
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Ignition switch ON



    2. B229710E01
    3. Waveform 2
      Tester Connection
      E77-20 (IMO) - B49-12 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.