Home › DRIVE LINE ยท VF4B TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSFER INDICATOR SWITCH


C133826E01
  1. Remove the indicator switches and gaskets.

    HINT:
    Indicator switch:
    No. 2
    Indicator switch (L4 position)
    No. 3
    Indicator switch (differential lock)



2. REMOVE TRANSFER GEAR SHIFT HEAD


G034493E01
  1. Using a pin punch and hammer, tap out the 2 slotted pins from the No. 1 and No. 2 gear shift heads.

  1. Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft and the high and low shift fork shaft.



3. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY


C111638
  1. Remove the 5 bolts and the bearing retainer.

    HINT:
    If necessary, tap the bearing retainer with a plastic-faced hammer to remove it.



4. REMOVE TRANSFER COVER TYPE T OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the bearing retainer.

    NOTICE:
    Be careful not to damage the oil seal and bearing retainer contact surfaces.



5. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY


C111616
  1. Remove the 4 bolts and retainer.



6. REMOVE BREATHER OIL DEFLECTOR


7. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front)
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    F043429E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    F043430E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



8. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.



9. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear)
  1. Remove the companion flange (rear) in the same way as the companion flange (front).

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



10. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear)
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.



11. REMOVE SPEEDOMETER DRIVEN GEAR ASSEMBLY WITH VEHICLE SPEED SENSOR


    G022561
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor with driven gear.



12. REMOVE SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY


    C113235
  1. Remove the clip and driven gear from the sensor.



    C113234
  1. Remove the O-ring from the driven gear.



13. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
  1. Remove the 5 bolts and the extension housing.

    HINT:
    If necessary, tap the extension housing with a plastic-faced hammer to remove it.



14. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the oil seal and extension housing contact surfaces.



15. REMOVE TRANSFER OUTPUT SHAFT WASHER
  1. Remove the 2 washers and the drive gear.



16. REMOVE REAR TRANSFER CASE


C116761
  1. Remove the 12 bolts and 2 clamps.

  1. Remove the rear case.

    HINT:
    If necessary, tap the rear case with a plastic-faced hammer to remove it.



17. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE


C116762
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a pin punch and hammer, drive out the slotted spring pin.

  1. Using a hexagon wrench, remove the No. 1 plug.

  1. Using a magnetic finger, remove the spring and ball from the hole.

  1. Remove the No. 2 gear shift fork and high and low shift fork shaft.

  1. Using a magnetic finger, remove the straight pin.

  1. Remove the high and low clutch sleeve, 3 shifting keys and 2 No. 1 springs.



18. REMOVE CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE


C116763
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a pin punch and hammer, drive out the slotted spring pin.

  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

  1. Using a hexagon wrench, remove the No. 2 plug.

  1. Using a magnetic finger, remove the spring and ball from the hole.

  1. Remove the center differential lock fork, shift shaft stopper, 2 springs, 3 stoppers, front drive shift shaft and front drive clutch sleeve.



19. REMOVE REAR TRANSFER OUTPUT SHAFT, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY


C111627
  1. Mount the rear case in a vise.

    NOTICE:
    Place aluminum plates on the vise to prevent damage to the rear case.

  1. Using a snap ring expander, remove the snap ring.



    C116764
  1. Using a plastic-faced hammer, carefully tap the rear case, and remove the output shaft together with the front drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the front drive chain.



20. REMOVE TRANSFER DRIVEN SPROCKET BEARING


F043523
  1. Using a press, press out the bearing.

    NOTICE:
    Be careful not to drop or damage the driven sprocket.



21. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING


F043524E01
  1. Using SST, a press and steel bar, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the driven sprocket.



22. REMOVE NO. 1 TRANSFER CASE PLUG (for Filler)
  1. Remove the filler plug and gasket.



23. REMOVE NO. 1 TRANSFER CASE PLUG (for Drain)
  1. Remove the drain plug and gasket.



24. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


F043446
  1. Remove the 3 bolts and separator.



25. REMOVE TRANSFER CASE MAGNET


26. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY


F043447
  1. Remove the 3 bolts and pump body.



27. REMOVE TRANSFER OIL PUMP BODY O-RING


F043462
  1. Using a screwdriver, remove the O-ring from the pump body.

    NOTICE:
    Be careful not to damage the pump body.



28. REMOVE TRANSFER OIL PUMP GEAR


F043448
  1. Remove the nut and pump gear.



29. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT


F043449
  1. Using a snap ring expander, remove the snap ring.



    C116765
  1. Remove the low planetary gear with input shaft.



30. REMOVE TRANSFER FRONT DRIVE CLUTCH SYNCHRONIZER RING


31. REMOVE OUTPUT SHAFT SPACER


C116766E01


32. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


33. REMOVE TRANSFER CASE OIL SEAL
  1. Using a screwdriver and hammer, tap out oil seal No. 1.

  1. Using a screwdriver and hammer, tap out oil seal No. 2.

    NOTICE:
    Be careful not to damage the oil seal and front case contact surfaces.



34. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING


C116767
  1. Using a snap ring expander, pry out the snap ring.



35. REMOVE TRANSFER INPUT GEAR STOPPER


C116768E01


36. REMOVE TRANSFER INPUT GEAR STOPPER BALL


37. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER


38. REMOVE TRANSFER INPUT SHAFT


C116769E01


39. REMOVE NO. 1 TRANSFER THRUST BEARING RACE


40. REMOVE TRANSFER LOW PLANETARY GEAR BEARING


41. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


C116770
  1. Remove the 2 seal rings.



42. REMOVE TRANSFER INPUT SHAFT BEARING


F043467E01
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST and a press, press out the bearing.

    SST
    09554-30011  
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the low planetary gear.



43. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE


C116775
  1. Using a screwdriver, remove the snap ring.

    NOTICE:
    Be careful not to damage the spline piece.

  1. Remove the spline piece.



44. REMOVE TRANSFER LOW PLANETARY GEAR BEARING


F043526E01
  1. Using SST, remove the bearing.

    SST
    09612-65014   (09612-01030, 09612-01050)

    NOTICE:
    Hang SST securely between the bearing and low planetary gear.



45. REMOVE TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING


C116778E01
  1. Using a snap ring expander, remove the snap ring.



46. REMOVE NO. 2 TRANSFER OUTPUT SHAFT SPACER


47. REMOVE TRANSFER OUTPUT SHAFT SPACER BALL


48. REMOVE CENTER DIFFERENTIAL CASE


49. REMOVE TRANSFER CLUTCH HUB


C116779E01


50. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING


51. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER


52. REMOVE TRANSFER OUTPUT SHAFT REAR RADIAL BALL BEARING


C116780E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  



53. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


C116781E02


54. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


55. REMOVE TRANSFER DRIVE SPROCKET BEARING


56. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER


57. REMOVE TRANSFER CASE PLUG


F043455E01


58. REMOVE COMPRESSION SPRING


59. REMOVE TRANSFER CASE STRAIGHT PIN


60. REMOVE TRANSFER LOW PLANETARY RING GEAR


F043456
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the ring gear and front case.

  1. Remove the ring gear from the front case.