Home › SUSPENSION & AXLE › AXLE › AXLE SYSTEM

AXLE SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY


F042731
  1. Remove the bolt and separate the brake tube bracket from the steering knuckle.



    C168980
  1. Using a union nut wrench, separate the brake tube from the front disc brake caliper assembly.

    HINT:
    Use a container to collect the brake fluid as it drains out.



    F050211
  1. Remove the 2 bolts and front disc brake caliper assembly.



3. REMOVE FRONT DISC
  1. Place matchmarks on the disc and the axle hub and remove the disc.



4. REMOVE FRONT AXLE HUB GREASE CAP (for 4WD)


F042729
  1. Using a screwdriver and a hammer, remove the front axle hub grease cap.

    NOTICE:
    Do not damage the axle hub.



5. INSPECT FRONT AXLE HUB BEARING


F042746
  1. Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash is greater than the maximum, replace the bearing.



    F042745
  1. Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the bearing.



6. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)


7. INSTALL FRONT DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.

    HINT:
    When replacing the disc, select the position that gives the minimum disc runout.



8. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    F050211
  1. Install the front disc brake caliper assembly with the 2 bolts.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }



    F042731
  1. Install the brake tube bracket onto the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    C168981E02
  1. Using a union nut wrench, install the brake tube onto the front disc brake caliper assembly.
    Text in Illustration 
    *a
    Fulcrum Length

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



9. BLEED BRAKE LINE
  1. Turn the ignition switch on (IG).

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off (IG).

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level .



10. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }



11. REMOVE REAR WHEEL


12. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


C133098
  1. Remove the 2 bolts and 2 washers and separate the disc brake caliper assembly.

    NOTICE:
    Suspend the disc brake caliper assembly with a piece of rope.



13. REMOVE REAR DISC
  1. Release the parking brake lever.



    D028126E05
  1. Place matchmarks on the disc and axle hub and remove the disc.

    HINT:
    If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.



14. INSPECT REAR AXLE SHAFT BEARING


F042748
  1. Inspect the axle shaft backlash.

    1. Using a dial indicator, check the backlash near the center of the axle shaft.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash is greater than the maximum, replace the bearing.



    F042747
  1. Inspect the axle shaft runout.

    1. Using a dial indicator, check the runout of the surface of the axle shaft.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the bearing.



15. INSTALL REAR DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.



16. ADJUST PARKING BRAKE SHOE CLEARANCE


D028131E01
  1. Provisionally install the 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the disc locks.

  1. Contract the shoe adjuster until the disc rotates smoothly.

    Standard:
    Return 8 notches

  1. Install the hole plug.



17. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


C133098
  1. Install the disc brake caliper with the 2 bolts and 2 washers.

    Torque:
    105 N*m{ 1,071 kgf*cm , 78 ft.*lbf }



18. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }