Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using a Techstream to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester ON.

  4. Enter the following menus: Select: Body Electrical / Main Body or Back Door / Data List.

  5. According to the display on tester, read the "Data List".

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver door courtesy switch signal/ON or OFF
    ON :Driver door is open
    OFF: Driver door is closed
    -
    P Door Courtesy SW
    Front passenger door courtesy switch signal/ON or OFF
    ON: Front passenger door is open
    OFF: Front passenger door is closed
    -
    Rear Door Courtesy SW
    Rear door courtesy switch signal/ON or OFF
    ON: Either right or left rear door is open
    OFF: Both right and left rear doors are closed
    -
    Luggage Courtesy SW
    Back door and back window courtesy switch signal/ON or OFF
    ON: Either back door or back window is open
    OFF: Both back door and back window are closed
    -
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal / ON or OFF
    ON: Driver side door is unlocked
    OFF: Driver side door is locked
    -
    Passenger Lock Pos SW
    Passenger side door unlock detection switch signal / ON or OFF
    ON: Passenger side door is unlocked
    OFF: Passenger side door is locked
    -
    Rear Lock Position SW
    Back door unlock detection switch signal / ON or OFF
    ON: Back door is unlocked
    OFF: Back door is locked
    -
    Door Lock SW-Lock
    Door manual lock switch signal ON or OFF
    ON: Door control switch is pushed to lock position
    OFF: Door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch is pushed to unlock position
    OFF: Door control switch is not pushed
    -
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder or passenger side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder or passenger side door key cylinder is not turned
    -
    P Door Key SW-UL
    Door key linked lock switch signal / ON or OFF
    ON: Passenger side door key cylinder is turned to unlock position
    OFF: Passenger side door key cylinder is not turned
    -
    D Door Key SW-UL
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -

    Back Door: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key Linked Lock SW
    Door key linked lock switch signal / ON or OFF
    ON: Back door key cylinder is turned to lock position
    OFF: Back door key cylinder is not turned
    -
    Door Key Linked Unlock SW
    Door key linked lock switch signal / ON or OFF
    ON: Back door key cylinder is turned to unlock position
    OFF: Back door key cylinder is not turned
    -


PERFORM ACTIVE TEST

HINT:
Using a Techstream to perform Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect a Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester ON.

  4. Enter the following menus: Select: Electrical Body / Main Body or Back Door / Active Test.

  5. According to the display on tester, perform the "Active Test".


Main Body: 
Tester Display
Test Part
Control Range
Door Lock
Operate door lock motor LOCK/UNLOCK
-

Back Door: 
Tester Display
Test Part
Control Range
Door Lock
Operate door lock motor LOCK/UNLOCK
-