Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU

B136051E01


B136052E01

  1. Disconnect the main body ECU connectors.

  2. Measure the voltages of the wire harness side connectors.

    Standard voltage: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1H-2 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1V
    1B-4 (BECU) - Body ground
    W-R - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    1E-9 (BDR1) - Body ground
    B-Y - Body ground
    Power source circuit (From battery)
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-14 (KSW) - Body ground
    G-Y - Body ground
    Key unlock warning switch input
    Key inserted →
    Key removed from ignition key cylinder
    Below 1 V → 11 to 14 V
    E7-7 (BCTY) - Body ground
    W - Body ground
    Back door courtesy switch and back window courtesy switch input
    Back door or back window is open
    Below 1V
    Back door and back window are closed
    11 to 14 V
    E7-11 (RLCY) - Body ground
    P-B - Body ground
    Rear LH door courtesy switch input
    Rear LH door open
    Below 1V
    Rear LH door closed
    11 to 14 V
    E7-12 (RRCY) - Body ground
    P-L - Body ground
    Rear RH door courtesy switch input
    Rear RH door open
    Below 1V
    Rear RH door closed
    11 to 14 V
    E7-23 (DCTY) - Body ground
    R-B - Body ground
    Driver door courtesy switch input
    Driver door open
    Below 1V
    Driver door closed
    11 to 14 V
    E7-24 (PCTY) - Body ground
    R-B - Body ground
    Front passenger door courtesy switch input
    Front passenger door open
    Below 1V
    Front passenger door closed
    11 to 14 V
    E7-3 (PRG) - Body ground
    G-O - Body ground
    Door control receiver output
    Key inserted in ignition key cylinder → As key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    E7-4 (RDA) - Body ground
    L-R - Body ground
    Door control receiver input
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation
    1J-14 (HAZ) - Body ground
    W - Body ground
    Hazard warning light signal
    Answer-back OFF → ON
    Pulse generation
    1B-10 (BZR) - 1B-6 (BZR2)
    P-B - Y-B
    Wireless door lock buzzer signal
    Wireless door lock buzzer OFF → ON
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK DOOR CONTROL RECEIVER

B133370E01

  1. Disconnect the door control receiver connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E23-5 (+B) - E23-1 (GND)
    R - W-B
    Battery (power supply)
    Always
    11 to 14 V
    E23-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the door control receiver connector.

  4. Measure the voltage of the wire harness side connector.

    Standard voltage: 
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E23-3 (PRG) - Body ground
    G-O - Body ground
    Signal input from main body ECU
    Key inserted in ignition key cylinder → As key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    E23-2 (RDA) - Body ground
    L-R - Body ground
    Signal output to main body ECU
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.