Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A056276E16
  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).
  2. The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
When either of following conditions are met (2 trip detection logic):
  1. In duration between engine warmed up and next engine starts, change in Intake Air Temperature (IAT) sensor output below threshold
  2. During engine warming up after cold engine starts, change in IAT sensor output below threshold
IAT sensor (built into MAF meter)

MONITOR DESCRIPTION

  1. After warmed engine stop
    The ECM monitors the intake air temperature variation in the period from when the engine was warmed up on the previous trip until the next engine start. If the change in engine coolant temperature sensor output is less than the threshold, it is determined that a malfunction has occurred in the intake air temperature sensor. When this is detected, the MIL is illuminated and the DTC is stored.
  1. After cold engine start
    The monitor runs when the engine is started cold after 5 hours or more have elapsed since the engine stopped. If the intake air temperature sensor output variation until the engine has warmed up completely is less than the threshold, it is determined that a malfunction has occurred in the intake air temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.

MONITOR STRATEGY


Related DTCs
P0111: Intake air temperature sensor rationality (After warmed engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
-
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
None

After Engine Stop 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or more
IAT sensor circuit fail (P0112, P0113)
Not detected
ECT sensor circuit fail (P0115, P0117, P0118)
Not detected
MAF meter circuit fail (P0102, P0103)
Not detected
Soak timer circuit fail (P2610)
Not detected
ECT change since engine stop
-40°C (-40°F) or more
ECT before engine stop
70°C (158°F) or more
Time that MAF is low before engine stop
35 minutes or more
Accumulated MAF amount before engine stop
6727 g or more
Key-off duration
30 minutes

After Cold Engine Start 
Key-off duration
5 hours
Time after engine start
10 seconds or more
IAT sensor circuit fail (P0112, P0113)
Not detected
ECT sensor circuit fail (P0115, P0117, P0118)
Not detected
MAF meter circuit fail (P0102, P0103)
Not detected
Soak timer circuit fail (P2610)
Not detected
ECT
70°C (158°F) or more
Accumulated MAF amount
6727 g or more
Either of the following conditions 1 or 2 is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


After Engine Stop 
IAT change
Less than 1°C (2°F)

After Cold Engine Start 
IAT change
Less than 1°C (2°F)

CONFIRMATION DRIVING PATTERN


A198822E13

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].

    HINT:
    During steps [A] through [C], if the change in the intake air temperature is less than 1°C (1.8°F), the intake air temperature sensor (MAF meter) is malfunctioning. It is not necessary to continue this procedure.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0111.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].

  13. Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Check the DTC judgment result again [F].

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0112 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0111 and other DTCs are output
    A
    P0111 is output
    B

    HINT:
    1. If any DTCs other than P0111 are output, troubleshoot those DTCs first.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART (Click here)